User manual MCINTOSH MVS3

[. . . ] 18 How to Reassign Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 How to Operate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Specifications and Packing Instruction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 4 NOTE: The MVS3 can be operated together with a McIntosh Control Center or Surround Decoder with a Power Amplifier. [. . . ] Connect this equipment only to the type of AC power source as marked on the unit. Route AC power cords so that they are not likely to be 7 Safety Instructions cont walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the instrument. Non-polarized line cord adapters will defeat the safety provided by the polarized AC plug. If the plug should fail to fit, contact your electrician to replace your obsolete outlet. Do not overload wall outlets, extension cords or integral convenience receptacles as this can result in a risk of fire or electric shock. 8 Care of Equipment: 18. Unplug this equipment from the wall outlet and clean the panel with a cloth moistened with a window cleaner. Do not permit objects of any kind to be pushed and/or fall into the equipment through enclosure openings. Unplug the power cord from the AC power outlet when left unused for a long period of time. Safety Instructions cont Repair of Equipment: 21. Unplug this equipment from the wall outlet and refer servicing to a qualified service personnel under the following conditions: A. Objects have fallen, or liquid has been spilled into the equipment, C. The equipment does not operate normally by following the operating instructions contained within this owners manual. Adjust only those controls that are covered by the operating instructions, as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation, E. The equipment exhibits a distinct change in performance - this indicates a need for service. Do not attempt to service beyond that described in the operating instructions. When replacement parts are required, be sure the service technician has used replacement parts specified by McIntosh or have the same characteristics as the origi9 Safety Instructions cont, Introduction, Performance Features and Installation nal part. Unauthorized substitutions may result in fire, electric shock, or other hazards. Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition. Performance Features Introduction The McIntosh MVS3 Audio/Video Source Selector provides you with the capability of selecting up two five different Audio/Video sources when used together with a McIntosh Control Center or Surround Decoder. It will also allow you to reassign the five inputs for specific sources. 10 Selection up to five different Audio/Video Sources Data Control Connections, Remap Inputs S-Video, Composite Video and Audio Connections RF Modulator Output Installation The MVS3 can be placed upright on a table or shelf. Cool operation ensures the longest possible operating life for any electronic instrument. Do not install the MVS3 directly above a heat generating component such as a high powered amplifier. How to Connect with a Surround Decoder How to Connect with a Surround Decoder 1. Connect a cable from the MVS-3 LV DATA OUTPUT to the LV player CONTROL (DATA) jack, from the MVS-3 LV AUDIO INPUTS to the player LV AUDIO OUT jacks and a Video cable (either S or Composite) from the MVS-3 LV VIDEO INPUT to the matching VIDEO OUT on the LV player. Connect the MVS-3 VCR1 AUDIO/VIDEO INPUTS to the Audio/Video Outputs of the VCR1. [. . . ] After selecting the desired program source, operate the source component according to its owners manual instructions, and then refer to the MAC-3 Owners manual for operating details. How to operate with a Control Center Select the desired input source with the Listen switch or the Remote Control. Operate the Control Center and associated 21 A/V components as directed by their respective owners manuals. How to use a Satellite receiver that has an analog output The MAC-3 can be reassigned to accept Analog audio signals from a satellite receiver, when the SAT digital input is selected. [. . . ]