User manual MAXDATA VISION 450T

[. . . ] Notebook Vision 350M Vision 450T i Notice The information in this user`s manual is subject to change without notice. THE MANUFACTURER OR RESELLER SHALL NOT BE LIABLE FOR ERRORS OR OMISSIONS CONTAINED IN THIS MANUAL AND SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL DAMAGES, WHICH MAY RESULT FROM THE PERFORMANCE OR USE OF THIS MANUAL. No part of this manual may be photocopied or reproduced in any form without prior written authorization from the copyright owners. Copyright April, 2000 All rights reserved. Microsoft and Windows are registered trademarks of Microsoft Corporation. Product names mentioned herein may be trademarks and/or registered trademarks of their respective owners/companies. [. . . ] Please observe the following instructions carefully or have a qualified technician install it for you. Damages due to mishandling of this procedure is NOT covered by the manufacture's warranty. Warning: Changing memory while your computer is in suspend or power-saving mode may cause permanent damage to the notebook. Make sure you turn off the power and unplug the AC cord before proceeding with a memory upgrade. 4-6 Section 4 UPGRADING YOUR NOTEBOOK Expanding The DIMM Module In The Original Socket To expand the DIMM, do the following: Warning: To avoid damaging the DIMM, do not touch its metal contact edge to avid the electrostatic damage from static electricity. 1. Place your hand on a large metal object momentarily to discharge any static electricity. Find the keyboard latches A, B and C near the bottom edge of the keyboard refering to the figure as below. It will retract when pressed and revert back to its original position when released. Illustration 4-3 Fn C trl C trl Alt A lt Del Latch A Latch B Bottom Edge of Keyboard Latch C 5. If the keyboard does not pop up, try to gently lift it up just over the latch. Carefully lift up the bottom edge of the keyboard and the following is revealed. 4-7 USER`S MANUAL PCB Connector Slot Original Memory Socket Fixing Screws DIMM Module Expansion Memory Socket Latch A Latch B Latch C Flexible PCB (The bridge between keyboard and the mainboard. ) Keyboard Illustration 4-4 Note: Your notebook has been tested with a wide range of DIMM on the market. Check with your notebook vendor for a list of compatible DIMM for your notebook. 7. Press out on the latches located on both edges of the socket at the same time. The DIMM should pop up to an angle of 30 degree. 4-8 Section 4 UPGRADING YOUR NOTEBOOK 9. Slide the DIMM at an angle of approximately 30 degrees into the empty memory socket. Then press it firmly so that the contact edge is driven into the receiving socket. Note: Notice the notches on the DIMM. The notches should fit nicely with the socket. Notch Illustration 4-6 DIMM Module Memory Socket 11. Pivot the DIMM until the latches on both sides of the socket snap into place. You have just completed the memory upgrade. 4-9 USER`S MANUAL Installing the DIMM Module In The Expansion Socket To remove the memory module, do the following: 1. Follow steps 1~7 in the above section, Installing the DIMM Module In The Memory Socket. Hold the extended memory module at a 30-degree angle and slide it into the empty momery socket. Notch DIMM Module Memory Socket 3. Align the small notch in the module with the socket on the connector and gently push it in and down until it clicks in place. Pivot the DIMM until the latches on both sides of the socket snap into place. You have just completed the memory upgrade. 4-10 Section 4 UPGRADING YOUR NOTEBOOK Removing the DIMM Module In The Expansion Socket To remove the memory module, do the following: 1. Follow steps 1~7 in the above section, Installing the DIMM Module In The Memory Socket. [. . . ] n Do not expose the battery pack to high storage temperatures (above 60oC, 140oF). n When discarding a battery pack, contact your local waste disposal provider regarding local restrictions on the disposal or CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturer`s instructions or local laws. VORSICHT! [. . . ]