User manual MAGNAT MC 1

[. . . ] 10 GB TABLE OF CONTENTS ACCESSORIES 1) 2) 3) 4) 5) 6) 1 Instruction manual Remote control Batteries for remote control (2x AA) Mains cable MW loop antenna FM indoor antenna 2 3 11 12 Accessories Before starting 12 12 Safety precautions Instructions for disposal 13 Operational elements and connections 13 14 15 Front panel Remote control Rear/connections 15 Installation 15 15 15 15 15 Speakers Antennas Auxiliary audio devices Initial operation Remote control 4 5 6 16 Functions of the MC 1 16 16 17 17 18 Functions of the CD player Functions of the tuner RDS (Radio Data Service) functions of the tuner Sound settings Sleep function 18 18 Other important information Specifications 11 GB BEFORE STARTING Dear customer, Thank you for choosing the Magnat MC 1 SACD/CD Receiver. Please read the following information carefully before starting to use the MC1. IMPORTANT SAFETY PRECAUTIONS • • • • Please read the instruction manual carefully before use and keep it in a safe place This device is only intended for use with 230 V/50 Hz AC voltage. Only operate the device at an ambient/room temperature between 0°C and 40°C. [. . . ] SPEAKERS The stereo speakers (impedance of 4 to 8 ohms) are connected to the rear as follows: right left 12 11 10 1 2 3 4 5 6 7 8 9 1 Mains connection For connecting the supplied mains cable. 2 Power switch Switches the device on and sets it in the standby mode. If the switch is set to the "OFF" position, the device is disconnected from the mains supply. 3 Speaker terminals For the connection of stereo speakers with an impedance rating of 4-8 ohms (the correct polarity must be taken into account). 7 AUX input This is where an auxiliary CD player or tuner can be connected. 8 TAPE input For the connection of a cassette recorder or a tape recorder. 9 PHONO input Low level input with RIAA equalisation for record players with a magnetic system (MM). 10 Earth for phono cable This is where the earth connection of the phono cable is screwed. 11 AM antenna connection For connecting the supplied AM loop antenna. 12 FM antenna connection For connecting the supplied FM indoor antenna or a house antenna. Only use high-quality audio speaker cables with a conductor cross section of min. Loosen the terminal screws one after the other and insert the stripped ends into the holes. You can also use prefabricated cables with 4mm banana plugs or forked fittings. ANTENNAS Connect the FM indoor antenna or a house antenna (provides better reception) to the rear of the device (12), as well as the MW loop antenna (if required). aUXILIARY AUDIO EQUIPMENT Auxiliary audio devices (MP3 players , record players , etc. ) are to be connected to the appropriate sockets before starting to use the MC 1. REMOTE CONTROL When using the remote control aim it at the infrared sensor on the MC 1 (front panel/13). ~ 30° ~ 30° -- Sensor 15 GB FUNCTIONS OF THE MC 1 FUNCTIONS OF THE CD PLAYER Playing a CD • Open the CD compartment by pressing the EJECT button. € Insert the CD into the compartment (with the label facing upwards). SACD Display: pressing the button again will stop the search function. FUNCTIONS OF THE TUNER Selecting the tuner band • Select TUNER as the audio source using the SOURCE (MC 1) or INPUT button (on the remote control). € Select AM mono, FM mono or FM stereo using one of the FM/AM buttons. [. . . ] Signal to noise ratio: CD/Aux/Line/Tape Phono Input sensitivity/impedance: AUX/Line/Tape Phono Equalisation: Bass Treble FM Tuner Frequency response: Signal to noise ratio: Mono Stereo Harmonic distortion: Mono Stereo AM Tuner Frequency response: Signal to noise ratio: Miscellaneous OTHER IMPORTANT INFORMATION Headphones • You can connect headphones with a 3. € The sound from the speakers is automatically disconnected when headphones are inserted. € Please note that listening to music at high volume via headphones can cause irreparable damage to your hearing!Line in (front panel) • This is used for connecting an audio source with a 3. [. . . ]