User manual MACH SPEED P4MST-890 SETUP MANUAL

[. . . ] P4MST-890 Setup Manual FCC Information and Copyright This equipment has been tes ted and found to comply with the limits of a Class B digital devic e, purs uant to Part 15 of the FCC Rules . T hese limits are designed to provide reasonable protec tion against harmful interference in a residential installation. T his equipment generates , uses and can radiate radio frequency energy and, if not ins talled and used in accordance with the instructions , may cause harmful interference to radio communications . There is no guarantee that interference will not occur in a particular ins tallation. The vendor makes no representations or warranties with respec t to the contents here and s pecially disclaims any implied warranties of merchantability or fitness for any purpose. [. . . ] It provides ASL code for power management and devi ce con figu ration cap abilities as defined in the ACPI speci fication, developed by Microsoft, Intel and Toshiba. PCI Bus Support This PHOENIX-AWARD BIOS also supports Version 3. 0 of the Int el PCI (Peripheral Component Interconnect) local bus specification. DRAM Support DDR SDRAM (Double Data Rate Synchronous DRAM) is supported. Supported CPUs This PHOENIX-AWARD BIOS supports the Intel CPU. Using Setup Use the arrow keys to highlight items in most of the place, press <Enter> to select, use the <PgUp> and <PgDn> keys to change entries, press <F1> for help and press <Esc> to quit. The following table provides more detail about how to navigate in the Setup program by using the keyboard. Keystroke Up arrow Down arrow Left arrow Right arrow Move Enter PgUp key PgDn key + Key - Key Esc key F1 key F5 key F7 key F10 key Function Move to previous item Move to next item Move to the item on the left (menu bar) Move to the item on the right (menu bar) Move to the item you desired Increas e the numeric val ue or make c hanges Decrease the numeric value or make changes Increas e the numeric val ue or make c hanges Decrease the numeric value or make changes Main Menu ­ Quit and not s ave c hanges into CMOS Status Page Setup Menu and Option Page Setup Menu ­ Exit Current page and r eturn to M ain Menu General help on Setup navigation keys Load pr evious values from CMOS Load the opti mized defaults Save all the CMOS c hanges and exit 2 P4MST-890 1 Main Menu Once you enter Phoenix-Award BIOSTM CMOS Setup Utility, the Main Menu will appear on the screen. Use the arrow keys to select among the items and press <Enter> to accept and enter the sub-menu. !!WARNING !! For better system performan ce, the BIOS firmware is being continuously updated. The BIOS information described in this manual (Figure 1, 2, 3, 4, 5, 6, 7, 8, 9) is for your reference only. The actual BIOS information and settings on board may be slightly different from this manual. Figure 1: Main Menu Standard CMOS Features This submenu contains industry standard configurable options. Advanced BIOS Features This submenu allows you to configure advanced features of the BIOS. 3 P4MST-890 Advanced Chipset Features This submenu allows you to configure special chipset features. Integrated Peripherals This submenu allows you to configure cert ain IDE hard drive options and Programmed Input/ Output features. Power Management Setup This submenu allows you to configure the power managem ent features. PnP/PCI Configurations This submenu allows you to configure cert ain " Plug and Play" and PCI options. PC Health Status This submenu allows you to monitor the hardware of your system. Performance Booster Zone This submenu allows you to change CPU Vcore Voltage and CPU/PCI clock. Changing the voltage and clock improperly may damage the CPU or M/B!) Load Optimized Defaults This selection allows you to reload the BIOS when problem occurs during system booting sequence. A confirmation message will be displayed before d efaults are set. 4 P4MST-890 Set Supervisor Password Setting the supervisor password will prohibit everyone except the supervisor from making changes using the CMOS Setup Utility. You will be prompted with to enter a password. Set User Password If the Supervisor Password is not set, then the User Password will function in the same way as the Supervisor Password. If the Supervisor Password is set and the User Password is set, the "User" will only be able to view con figurations but will not be able to change them. Save & Exit Setup Save all configuration changes to CMOS (memory) and exit setup. Confirmation message will be displayed before proceeding. Exit Without Sa ving Abandon all changes made during the current session and exit setup. Confirmation message will be displayed befo re proceeding. 5 P4MST-890 Upgrade BIOS This submenu allows you to upgrade bios. 6 P4MST-890 2 Standard CMOS Features The items in Standard CMOS Setup Menu are divided into several categori es. Use the arrow keys to highlight the item and then use the<PgUp> or <PgDn> keys to select the value you want in each item. Figure 2: Standard CMOS Setup Main Menu Selections This table shows the items and the available options on the Main Menu. Item Date Options mm : dd : yy Description Set the system date. Note that the `Day ' automatically changes when you set the date. Press <Enter> to enter the sub menu of detailed options Press <Enter> to enter the sub menu of detailed options. Time IDE Channel 0 Master hh : mm : ss Options are in its sub menu. Options are in its sub menu. IDE Channel 0 Slav e 7 P4MST-890 Item IDE Channel 1 Master Options Options are in its sub menu. 360K, 5. 25 in 1. 2M, 5. 25 in Description Press <Enter> to enter the sub menu of detailed options. Press <Enter> to enter the sub menu of detailed options. IDE Channel 1 Slav e Driv e A Driv e B 720K, 3. 5 in 1. 44M, 3. 5 in 2. 88M, 3. 5 in None All Errors No Errors Select the ty pe of f loppy disk drive installed in your sy stem. Halt On All, but Key board All, but Diskette All, but Disk/ Key Select the situation in which y ou want the BIOS to stop the POST process and notify y ou. [. . . ] By Choosing "Manual", the user will need to assign IRQ & DMA for add-on cards. The Choices: Auto (ESCD) (default), Manual. 33 P4MST-890 IRQ Resources This submenu will allow you to assign each system interrupt a type, depending on the type of device using the interrupt. When you press the " Press Enter" tag, you will be directed to a submenu that will allow you to configure the system interrupts. This is only configurable when " Resources Controlled By" is set to "Manual". [. . . ]