User manual LISTAESCAN STORAGE WALL DOORS INSTRUCTIONS

[. . . ] Chapter 2 Storage Wall Doors Lista provides three types of doors for Storage Walls: Sliding Doors, Tambour Doors, and Hinged Doors. This chapter provides step-by-step instructions for assembling and attaching each type of door. Sliding Doors Hinged Doors Tambour Door Leveling and Anchoring the Storage Wall Before you begin assembling and attaching doors, you should anchor the Storage Wall. With the Rear Panels or Sway Braces in place, move the Storage Wall to its permanent location. Note: Anchors are not supplied with the Storage Wall, and may require compliance with certain building codes. [. . . ] Attaching the Trolleys Step 1 2 Action (Refer to Figure 2-7, below and Figure 2-7A, page 6) Refer to Figure 2-7A. Thread a ¼-20 hex nut on a ¼-20 x 3-½" hex head bolt. Half-way into the door bracket, there will be a hole cut into the metal bracket. Finish inserting the bolt through the lower portion of the bracket and thread a ¼-20 square nut onto the bolt. Adjust the bolt so that the head of the bolt is close to the top of the door panel. Attach two Trolleys to each door by inserting the open slot of each Trolley into the 3 ½" Hex Head bolts at the top of the doors. The door with the lock assembly glides on the outer channel of the upper and lower tracks; position the trolleys so that the wheels face the front of the door. The door without the lock glides on the inner channel of the upper and lower tracks; position the trolleys so that the wheels face the back of the door. Attach the top stiffener to each door using #8 x 3/8" Phillips Pan Head screws. Figure 2-6 Sliding Door Lock Figure 2-7 Trolley 3 4 2-4 Figure 2-8 Triple-Sliding Door Set (36U Door Shown, Rear View) Figure 2-8A ­ Top view of Triple Sliding Door Set 2-5 Figure 2-9 Double-Sliding Door Set (36U Door Shown, Rear View) Figure 2-7A ­ Side Profile Figure 2-9A ­ Top view of Double Sliding Door Set 2-6 Inserting the Sliding Doors into the Upper and Lower Tracks From the right side of the Storage Wall (without the Door Frame attached), insert the door without the lock by sliding into the inner channels of the Upper and Lower tracks. Slide the second door (with the lock) into the outer channels of the upper and lower tracks. For a Triple-Door set, slide the third door into the inner channels of the Upper and Lower tracks. Triple Doors must always be placed on the right hand side of the Storage Wall System. Attaching the Right Door Frame Once all of the doors are installed into the Upper and Lower Tracks, you can attach the Right Door Frame. Step 1 2 3 4 5 Action (Refer to Figure 2-10) Attach the Right Door Frame to the right side of the Storage Wall using 5/16 x ¾" Hex Head bolts and nuts. Attach the two Unistrut nuts to the bottom of the Right Door Frame using 5/16 x ¾" x 82° Flat Head screws. Insert the screws down through the bracket of the Door Frame and into the Unistrut nuts. Slide the Lower Track into the Door Frame by positioning the Lower Track so that the Unistrut nuts fit into the front and back channels of the track. Position the Lower Track so that it is parallel with the Storage Wall. Tighten the 5/16 x ¾" x 82° Flat Head screws using a 3/16" Allen wrench. Secure the Upper Track to the Right Door Frame by inserting a Track Mount Bracket into each end of the Upper Track, as shown. Insert two 5/16 x ¾" 82° Flat Head screws up and through the top bracket of the Right Door Frame and into the Track Mount Bracket. Refer to Figure 2-10 below. Adjusting the Doors Test the lock system to make sure the doors are aligned. [. . . ] Mount the bottom-mounting rail to the bottom Universal Panel, as indicated in Step 2. Insert the two long plastic bushings into the two outer holes in the bottom-mounting rail. Pick up the following items: 1 short plastic bushing, 1 black clip, 2 chrome pins. Attaching the Doors Position the Left Door (the door without the handle) so that the hole in the lower left corner of the door lines up with the left lower bushing. [. . . ]