User manual LISTAESCAN STORAGE WALL COMPONENTS INSTRUCTIONS

[. . . ] Þ Location Against a Wall If the Storage Wall is to be permanently located against a wall, begin the assembly 2 ½ to 3 ½ feet away from the wall. The Storage Wall can then be pushed against the wall before you install the drawers or shelves. Þ Floor Level The floor must be level in all directions and should not exceed a total of 1" (25mm) of shimming. · · · · Check your packing list and bill of lading to make sure that all Storage Wall components are available before you begin the assembly. [. . . ] Align the hole patterns of the Upper Rear Panel and Vertical Side Frames. Insert ¼-20 x 5/8" Hex Head bolts through the Upper Rear Panel and into the Vertical Side Frames. Insert the Upper Rear Panel for the next section by sliding it down and into the tabs of the Horizontal Support Bracket. Overlap the Upper Rear Panel with the existing Upper Rear Panel and secure with ¼ x 5/8" Hex Head bolts and ¼ - 20 Kep nuts. 2 Note: To insert the Hex Head bolts easily into overlapped sections, use an awl or screwdriver to align the hole patterns of both panels. Note: For back-to-back installations with a common Rear Panel, insert ¼-20 x 5/8" Hex Head bolts through the overlapping Upper and Lower Rear Panels and into the Vertical Side Frames. Secure with ¼ - 20 Kep nuts from inside the Storage Wall. Attaching the Sway Braces If your Storage Wall configuration includes Rear Panels instead of Sway Braces, refer to "Attaching Rear Panels. " Sway Braces must be installed in the first, last, and at least every fourth intermediate Storage Wall section. Secure with ¼-20 x 5/8" Hex Head bolts and nuts, as shown in Figure 1-6. For back-to-back Storage Walls, insert the ¼-20x5/8" Hex Head bolts through the bracing and into the Vertical Side Frame on the other side as shown in Figure 1-7. Secure with ¼ - 20 Kep nuts. 1-4 Figure 1-4 Rear Panels Figure 1-5 Rear Panels (Upper and Lower) Figure 1-6 Sway Braces Figure 1-7 Sway Braces (Back-to-Back Storage Walls) 1-5 Attaching Center Universal Panels If your Storage Wall includes a Center Panel, the clearance between the Bottom and Center Panels should be indicated on the drawing you received from your Lista Representative. It is important to install the Center Panel in the position indicated to allow for proper installation of drawers or roll-out trays. Note: If you are installing a Full-Height Locking System, do not install the Center Locking Panel at this time. Most Storage Walls are configured with either 900mm or 1350mm of drawer points. Lista marks these heights with oblongshaped notches on the front and back of each Vertical Side Frame. Position the Center Panel so that its bottom edge covers the top half of the appropriate notch unless indicated otherwise in your drawing. Refer to your unique Storage Wall drawing (supplied by Lista) to determine the height of the drawer points for your specific installation. For example, if your drawing indicates 750mm of drawers within an individual section, the drawers will occupy 30 total slots (30 x 25mm), each slot equaling 25mm. Measure from the Floor Universal Panel up to determine the correct height for which the Center Universal Panel should be installed. Step Action (Refer to Figure 1-8) Insert four Shelf Clips into the notches of the Vertical Side Frames at the proper height and place the Center 1 Universal Panel down over the Shelf Clips. Secure using four 3/8 x 5/8" bolts and nuts (one for each corner of the Center Universal Panel). (All hardware should be tightened before installing drawers and trays). Note: If your Storage Wall includes a partial lock system, install the Center Universal Panel so that the hole for the cylinder lock faces the front of the Storage Wall. 2 For appearance purposes, push the Center Universal Panel as far back as possible so that it is flush with the Vertical Side Frames. [. . . ] Full Suspension Drawers or Roll-Out Trays consist of the following components: · · · · Drawer or Roll-Out Tray U-Tracks, Left and Right Suspension Frame Safety Clips Caution: Wear gloves when handling the U-Tracks. Each U-Track occupies three slots of Vertical Side Frame, or 75mm (3 x 25mm). Step 1 Action (Refer to Figure 1-21 and Figure 1-22) Hold the U-Track so that the tabs are in front and the prongs are in back. Install each U-Track in the proper mounting slot in the rear, making sure the tabs in front are firmly seated. Press a Safety Clip (with the points facing out) into the front notches on both the left and right Vertical Side Frames to lock the U-Track into place. 2 Note: If the Safety Clip doesn't seem to fit properly, it indicates that the U-Track is not firmly seated in its mounting slot. [. . . ]