User manual LISTAESCAN OVERHEAD CABINET WALL MOUNTING INSTRUCTIONS

[. . . ] 2 The Bolts that attach the lower Mounting Bracket to the wall will be placed 50mm [2"] above the height determined in step 1. 3 If pilot holes are required, use the Mounting Bracket as a template and mark the locations on the line for the Bolts. 5 Clip the filler channels into the ends of the lower mounting brackets. [. . . ] 6 Before the last mounting bracket is installed, attach the second filler channel as shown if fig 6 7 Level, square and secure the final mounting bracket to the wall. 8 Follow steps 10 thru 14 on page 2 to install the cabinets. Figure 6 Note: Install second Filler Channel before installing last Mounting Bracket . FLUSH WALL MOUNTING without MOUNTING BRACKETS TOOLS NEEDED FOR INSTALLATION · · · · Drill Level Tape Measure Ratchet Wrench Figure 7 COMPONENTS NEEDED FOR INSTALLATION · Hardware to mount cabinet to wall (Not Provided by Lista) INSTALLATION INSTRUCTIONS 1 Open the Cabinet 2 Remove the Adjustable Shelf (Ref. Adjustable Shelf Removal Instructions) 3 Remove the bottom shelf 4 Bolt the cabinet to the wall through the four obround holes provided. (Figure 7) Note: Make sure the cabinet is level before it is bolted to the wall. Adjustable Shelf Reinstallation Instructions) obround holes for flush mounting Page 4 Installation and Use Instructions for Frame Mounted Overhead Cabinets TOOLS NEEDED FOR INSTALLATION · · · · · Drill & Drill Bits Ratchet Wrench for mounting hardware 3 /1 " Allen Wrench 6 Philips Head Screwdriver Level MOUNTING FRAME ASSEMBLY TO A SINGLE BASE CABINET (See Figure 8) 1 Drill four (4) 3/ 8" diameter holes into the rear of the cabinet as shown in Figure 8. 2 Follow Steps 5 through 12 below. COMPONENTS NEEDED FOR INSTALLATION Upper Support Posts (2) Base Posts (2) Upper Mounting Rail (1) Lower Mounting Rail (1) Mounting Blocks (4 per cabinet) Rear Panel (1) (if ordered) 5/ 16"­18 x 3½" Bolts, nuts and washers (4 sets) ¼­20 x 5/8 hex head bolts and ¼ lock washers (4 sets) " ¼­20 x ½" Socket Cap Screws (4 per post) ¼­20 x ¾" Socket Cap Screws and lock washers (4 per cabinet) #10­24 x ½" Sheet Metal Screws (2 per cabinet) MOUNTING FRAME ASSEMBLY ACROSS MULTIPLE BASE CABINETS 1 Locate the base cabinets that go on the extreme ends of the workcenter. Remove the drawers from those cabinets 2 Drill four 3 /8" diameter holes in the rear of the cabinets as shown in Figure 8. 3 Place the cabinet, with holes drilled along the right rear edge, on the extreme right of the workcenter. 4 Place the cabinet, with holes drilled along the left rear edge, on the extreme left of the workcenter. Note: If using a Steel Cover over the Base Cabinets, refer to the Steel Cover/Base Post Instructions on Page 7 before installing Base Posts. and Upper Support Posts into the base posts . SAFETY PRECAUTIONS READ INSTALLATION INSTRUCTIONS BEFORE STARTING INSTALLATION USE CAUTION WHEN HANDLING SHEET METAL PARTS, THE EDGES MAY BE SHARP THIS INSTALLATION WILL REQUIRE AT LEAST 2 PEOPLE DO NOT OVERLOAD FRAME BEYOND RATED LOAD CAPACITY. ­ 40 LBS/LINEAR FT PER SHELF ­ 150 LBS MAX FOR THE 78U ADJUSTABLE SHELF DO NOT PLACE OBJECTS ON TOP OF THE CABINETS YOU MUST INSTALL SAFETY SCREWS TO PREVENT OHC FROM LIFTING OR SLIDING OFF MOUNTING RAILS 6 Slide the Upper Support Posts 7 Bolt the sub assemblies together using the 5 /16 ­18 x 3½" long Bolts, 5/ 16" Nuts and 5/ 16" Flat Washers . Note: The sub assemblies created are left and right specific as identified in Figure 9. 8 Using the ¼-20 x 5/ 8" Hex Head Bolts and ¼" Lock Washers , bolt the left and right sub-assemblies to the Base Cabinets. (Figure 10) 9 Attach the Upper Mounting Rails and Lower Mounting Rails to the Upper Support Posts using the ¼-20 x ½" Socket Head Screws and ¼" Lock Washers . (See Figure 10) 10 Attach the Mounting Blocks to the rear of the Overhead Cabinet(s) as shown in Figure 11. 11 Mount the Cabinet(s) to the frame assembly by clipping the Mounting Blocks onto the Frame Rails (See Figure 5 on page 3). OH Cabinet Base Cabinets Page 5 Figure 8 Drilling Locations Figure 9 37. 5 20 37. 5 20 20 20 Note: Dimensions are in millimeters Rear View of Base Cabinets Figure 10 Figure 11 Rear Panel Page 6 STEEL COVER/BASE POST INSTALLATION 1 Drill two (2) ½" holes in the top rear corners of the steel cover as shown in Fig. 3 Follow Steps 5 through 12 on Page 5. Figure 12 Figure 12a INSTALLING THE REAR PANEL (if provided) (See Figure 12 and 12a) If a Workcenter Top is used as the work surface: 1 Remove the backing from the double sided tape located on the bottom lip of the Rear Panel. [. . . ] (See Figure 15) 2 Slide the Support Bracket to the right until it locks into the right side slots. Slide mounting bracket in while pushing up on shelf to remove from housing. Page 7 CANOPY TOP INSTALLATION (See Figures 16 & 17) REQUIRED TOOL: Phillips Head Screwdriver 1 Using the #10­24 thread forming screws provided, attach the filler panel to the canopy. Note: This step is not required if the cabinet is screwed directly to the wall. 2 Remove the backing from the double sided tape already attached to the bottom of the canopy. [. . . ]