User manual LISTAESCAN NEXUS SYSTEM ASSEMBLY INSTRUCTIONS

[. . . ] Nexus Accessory System Instructions for Assembly Table of Contents General Information Standard Widths and Heights . . 8 TM Nexus Packing Bench Accessories Adjustable Shelves Without Lip . . 33 Nexus Stationary Stands and Mobile Trolley Nexus Stationary Stand Frames . . 27 Nexus Back Panels and Markerboard/Tackboards Louvered Back Panels . [. . . ] Insert ends of mouse tray (item 6) through both inner sets of holes on monitor tray. Insert (2) cotter hairpins (item 7) into holes at ends of mouse tray rods. Page 25 ACCESSORY / TOOL TRAY AND DOCUMENT TRAY INSTALLATION Tools Required: 7 · /16" Wrench Item 1 2 3 4 5 Step: 1. Description Articulating Arm Assembly Accessory/Tool Tray or Document Tray Flat Washer 5/16 Pivot Pin Plastic Nylon Washer 5. 05 x . 75 Qty. 1 1 1 1 1 Install articulating arm assembly (item 1) on post at height desired. Insert threaded end of pivot pin (item 4) into 5/16 flat steel washer (item 3). Insert pivot pin through hole on end of articulating arm assembly. Page 26 FLAT PANEL MONITOR BRACKET INSTALLATION Tools Required: · Hammer (rubber or regular) · Block of wood (to protect bracket from hammer) · Phillips head screwdriver · Wrench Item 1 2 3 4 Step: 1. Description Monitor Arm Mounting Bracket (Left & Right) Phillips Head Screw Hex Nut Wire Security Clip Qty. 4 4 1 Screw monitor arm base (monitor arm not shown) to left and right monitor arm mounting brackets (item 1) using (4) Phillips head screws (item 2) and (4) hex nuts (item 3). Note: Do not fully tighten bolts. Install top tabs of monitor arm mounting brackets into slots on post at height desired. 7. Make sure mounting brackets are fully seated and secure on post before installing wire security clips. Thread wire security clip (item 4) through hole in bottom of one of the mounting brackets. Page 27 NEXUS BACK PANELS AND MARKERBOARD / TACKBOARDS PEGBOARD, LOUVERED, SOLID AND WHITE / TACKBOARD PANELS Tools Required: 3 /16" Hex Key · 1 · /2" Wrench Item 1 2 3* 4 5 Description Panel (Pegboard, Louvered, Solid or White/Tackboard) Panel Support Bracket (Left & Right, Top & Bottom) Pegboard & Louvered Panel Stiffener Button Head Cap Screw 5/16 -18 x 5/8 Hex Nut 5/16 -18 Qty. 1 2 pair 1* 4 4 * Note: Stiffener used only with pegboard and louvered panels 18" or taller. 6. Bolt (4) panel support brackets (item 2) to four corners of the panel (item 1) using (4) 5/16-18 x 5/8 button head cap screws (item 4) and (4) 5/16-18 hex nuts (item 5). Insert lances of panel stiffener (item 3), used only with pegboard and louvered panels 18" or taller, into rear slots of panel. Insert tabs of panel support brackets into inner slots on posts at height desired. Fully tighten Cap Screws (item 4). Page 28 NEXUS PACKING BENCH ACCESSORIES ADJUSTABLE SHELVES WITHOUT LIP Tools Required: · No tools required Item 1 2 3 4 Step: 1. Description Packing Bench Adjustable Shelf Adjustable Shelf Mounting Bracket Security Clip Pan Head Screw 10-32 x 1/4" Qty. 1 2 2 2 Insert mounting brackets (item 2) into slots on bottom of adjustable shelf (item 1) as shown in Figure 2. Insert top tabs of mounting brackets into inner slots on posts at height desired and rotate downwards until edge 1 touches the front of the post, as shown in Figure 3. Press down to engage all three bracket tabs into the slots on the posts and to secure in place. ! 4. 8. Make sure shelf is properly installed to posts before installing security clips and before adding weight. Orient security clip (item 3) as shown in Figure 5. [. . . ] Insert (1) clevis pin (item 3) through the hole in mounting bracket then through post. Insert (2) clevis pins (item 3) through holes in document pocket and post. Insert (2) cotter hairpins (item 4) into holes in clevis pins. Page 41 FIXED FOOTREST FOR ALIGNTM Tools Required: 3 /16" Hex Key · 1 · /2" Wrench Item 1 2 3 4 5 6 7 8 9 Step: 1. Description AlignTM Workbench Horizontal Rail Variable Angle Shelf Post Black Plastic Plug 30 mm x 60 mm Top Bracket Bottom Bracket Button Head Cap Screw 5/16 -18 x 5/8 Hex Nut 5/16 -18 Hold Down Pin Qty. [. . . ]