User manual LENCO TFT-920

[. . . ] In the interest of safety, this system should never be installed where it will be visible, directly or indirectly, by the operator of the motor vehicle. Safety Precaution For safety reasons, when changing video media, it is recommended that the vehicle is not in motion, and that you do not allow children to unfasten seat-belts to change video media or make any adjustments to the system. Enjoy your entertainment system but always remember: safety of all passengers remains the number one priority. -1- Important Safety Instruction The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of un-insulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. To reduce the risk of electric shock, do not remove the cover (or back). [. . . ] Please take out the battery when the remote control is not used for a long time, in order to avoid damage to the remote control caused by possible liquid leakage. - 10 - Rechargeable Battery About Rechargeable Battery Pack Your portable DVB-T receiver can be connected with a lithium polymer rechargeable battery that attaches to the bottom of the unit. If the battery will not be used for a long period of time, first fully charge the battery prior to storage. Working conditions and precautions of the battery · · · · Battery should only be used and charged when temperatures are between 32ºF and 80ºF. Do not expose the battery to high temperatures or store in hot, sunny places. Maintain well-ventilated conditions around the product, avoiding heat. Don't put the product on bed, sofa or anything that may block ventilation to the product. Detach battery immediately after charging is complete if not being used. When charging the battery pack, the light on the battery will turn red, when the charging is complete or the battery is being used, the light will turn green. When the battery is weak, there will be a mark displayed on the LCD screen, and about one minute later, the unit will power off automatically. - 11 - Rechargeable Battery Battery Pack Attaching and Placement The unit's power supply is the AC power adapter or the battery pack. Place the unit on a soft and smooth surface with its back cover facing up (to avoid scratching the screen). Ensure that you observe the color coding when connecting audio and video cables. In TV mode, it outputs an analog audio signal; in DVB-T mode, it can output both analog and optical digital audio signal. - 14 - System Connections Connecting to an Amplifier The unit can be connected to an amplifier. SWAP Meant to swap the program number of a TV station with another TV station. Use the --/- button and the 0-9 numeric buttons to enter the target channel number, and then press the directional buttons to swap and exit from the menu. Then the currently playing channel will change to the target channel automatically. COPY Meant to copy the program of the current channel to a target channel. Use the --/button and the 0-9 numeric buttons to enter the target channel number, and then press directional buttons to copy and exit from the menu. Then the currently playing channel will change to the target channel automatically. NOTE: If the menu is not used for more than 10 seconds, the menu will disappear automatically. - 20 - DVB-T Setup Preparation 1. Press the MENU button on the remote control to enter the DVB-T setup menu. You can take the following steps to continue setup: Main Menu Press the MENU button, the screen will display the following: In the main menu, press the directional buttons to select the item you want to set up. Press the MENU or EXIT button to exit System Setting Press the directional buttons to select System Settings. Press the OK button to enter the submenu, screen will display as below: In the menu, press the buttons to select the item you want to configure, press the OK button to select the item. [. . . ] Select Channel No. , use the number buttons to input the channel No. , press the EDIT button to enter the character or number list, in the list, press the direction buttons to select character or number, press the OK button to confirm input, press the EXIT button to return. TPS Select TPS, use the numeric buttons to input, press the button to delete the input, press the EDIT button to enter the character or number list, in the list, press the directional buttons to select character or number, press the OK button to confirm input, press the EXIT button to return. BandWidth Select BandWidth, press the button to enter, then press the to select item, press the EXIT or button to return. Encrypted Service Select Encrypted Service, press the button to enter, and then press the directional buttons to select Save or No Save, press the EXIT or button to return. [. . . ]