User manual LENCO TFT-720

[. . . ] The unit applies the latest state of the art electronics and is designed for use in hotels, offices, vehicles or your home. The unit is constructed to provide years of reliable, trouble-free service, and is compact so that you can take it with you anywhere and is designed for quick and easy setup. The documentation will assist you in obtaining the best equipment performance. Save this manual for later use. Important Notice It is unlawful in most jurisdictions for a person to drive a motor vehicle which is equipped with a television viewer or screen that is located in the motor vehicle at any point forward of the back of the driver's seat, or that is visible, directly or indirectly, to the driver while operating the vehicle. [. . . ] Plug the A/V cable into the audio jack on the left side of the unit and plug the other end into an audio input on the amplifier. Please refer to the equipment's manual before connecting. In TV mode, it can output an analog audio signal; in DVB-T mode, it can output both an analog as an optical digital audio signal. It can be connected to a digital amplifier. Connecting to a DC Adapter Connect one end of the specific DC adapter to the "DC 12V IN" jack on the left panel of the unit, and connect the other end to the cigarette lighter socket in the car as shown below: · · The power supply of the car is not suitable for charging the battery. Make sure the unit is not connected to the car adapter when the car is started. - 15 - System Connections Connecting a Headphone Connect the headphone to the headphone jack on the left side of the unit. When headphones are connected, the speaker will be turned off automatically Connecting to DVB-T Antenna The unit is designed with an antenna input jack. Plug the DVB-T antenna into the jack on the right panel of the unit to receive TV signal, then slide the DVB /TV selector to DVB, As shown below: - 16 - System Connections Connecting to external antenna Plug the provided external antenna into the TV signal input jack on the right panel of the unit, as shown below. Then slide the DVB /TV selector (left side of unit) to TV. Connecting to CATV antenna Connect one end of the provided connecting line to the TV signal input jack on the right panel of the unit, and the other end to the CATV cable, as shown below. Then switch the DVB /TV selector to TV (left side of unit). - 17 - TV Setup Preparation 1. Press the TV SETUP button to enter the setup menu. Picture Setup Menu Press the TV SETUP button once to enter the Picture setup menu, as shown below: PICTURE COLOR BRIGHT CONTRAST 30 32 30 The items in the menu are used to adjust the brightness, contrast, and color of the screen. You can adjust the items in this menu to compensate for environment influences or to setup the screen to your own preference. TV Setup Menu Press the TV SETUP button twice to enter the TV setup menu, as shown below: TV SETUP SYSTEM CHANNEL FINE SKIP MANUAL AUTO PAL B/G 28 487. 25UHF OFF OFF In the TV Setup menu, press the SELECT or 1. Channel Press the SELECT or the channel number. buttons to select item. buttons to select buttons to select SYSTEM, press the buttons to select CHANNEL, press the buttons to select - 18 - TV Setup 3. Fine Tuning When reception quality is less than desirable, you can improve this with the fine tuning function. Press the SELECT or buttons to select FINE, press the button to start fine tuning, when video and audio are at their best, stop the fine tuning and the program will be stored automatically. Skip Press the buttons to select ON, the channel will be skipped when using the CH-/+ to select channels. Manual Searching Press the SELECT or buttons to select MANUAL, press the buttons to start searching, press the buttons again to stop searching, the programs searched will be stored automatically. Auto Searching Press the SELECT or buttons to select AUTO, press the buttons to select ON. It will take a few minutes, when searching is finished, it will exit and return to channel 1. All found programs will be placed in sequence. Function Setup Menu Press the TV SETUP button three times to enter the Function Setup menu, as shown here: FUNCTION LANGUAGE TIME OFF DEFAULT ENGL ___ In the Function setup menu, press the SELECT or 1. Language Press the SELECT or select different languages. buttons to select item. buttons to select LANGUAGE, press the buttons to 2. Time Off Press the SELECT or buttons to select TIME OFF, press the the time when the unit should shut itself off. Default Press the SELECT or the default setting. buttons to select button to select DEFAULT, press the OK button to return to - 19 - TV Setup Channel Editing Press the EDIT button on the remote control to enter the TV program edit mode. CHANNEL EDIT SWAP COPY CLEAR ALL - - - -- - -- - - Press the buttons to select different items. [. . . ] Update Mode Select Update Mode, press the button to enter, and then press the buttons to select Append or New, press the EXIT or button to return. directional After setting these items, use the directional buttons to highlight Start Search, and press the OK button to start searching. During searching, press the MENU or EXIT button to stop searching. - 25 - DVB-T Setup Sort Channel Select Sort Channel, press the button to enter, the screen will display as below: In the menu, press the directional buttons to select the desired item, press the OK button to confirm. Press the EXIT button to return to the previous menu. This setting is used to sort channels from A-Z or from Z-A or to encrypt the selected channel. Channel List Select the Channel List, press the OK button to confirm and enter, the screen will display as below: The first time you use this menu, you should add some programs into the channel list. [. . . ]