User manual LENCO CR-333

[. . . ] CR-333 OWNER S MANUAL Dual Alarm AM/FM Clock Radio with Triple Display, Touchless Snooze and Display Control and SmartSet ® Automatic Time Setting System TO PREVENT FIRE OR SHOCK HAZARD, DO NOT USE THIS PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. IMPORTANT SAFETY INSTRUCTIONS 1. ) Read these instructions. 5. ) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 6. ) Do not defeat the safety purpose of the polarized or grounding-type plug. [. . . ] To manually adjust the time display depress and hold the TIME button, and press either the SET (Up) or (Down) buttons to adjust the time display ahead or back as desired. Each press of the SET (Up) or (Down) buttons will change the display by one minute. If you hold the SET (Up) or (Down) buttons the display will continue to change. But if you continue holding the SET (Up) or (Down) buttons the display will change rapidly. NOTE: If you manually adjust the time, your new setting is entered into the SmartSet® memory. If the power is interrupted, the display will return to your new setting, not the original setting, when the power is restored. Adjusting The Wake Up Times Your SmartSet® clock radio has two separate alarms that can be set and used independently. You may use the alarms to wake two people at different times, or you may use one alarm for weekdays and the other for weekend wake up times. The procedure for adjusting the wake up time is the same for both Alarm 1 and Alarm 2. 6. ) When you are finished listening, press the RADIO ON/OFF button to turn the radio Off . The radio dial pointer light goes off. Antenna Information AM The AM bar antenna is inside the cabinet. If AM reception is weak, change the position of cabinet until the internal antenna picks up the strongest signal. FM The FM antenna is built in to the AC power cord. If FM reception is weak try varying the position and direction of the power cord until you find the strongest signal. Wake To RADIO 1. ) Turn the radio On and select the Band, Station, and Volume level that you wish to hear when the alarm comes on, then turn the radio Off again. 2. ) Reconfirm the wake up time and alarm mode settings for the alarm you are using, Alarm 1, Alarm 2, or both Alarms. 3. ) Set the ALARM selector switch for one or both alarms to the RADIO position. The appropriate ALARM 1 and/or ALARM 2 display will change from OFF to the selected wake up time. 5. ) To stop the radio sooner, press either the appropriate ALARM 1 or ALARM 2 button, or press the RADIO ON/OFF button. The radio will stop but the alarm remains set and will turn the radio on again at the same time on the following day (depending on the Alarm Mode setting). 6. ) If you do not want the alarm to turn the radio on the following day, set the appropriate ALARM selector to the OFF position. The respective alarm display will show OFF . Wake To BUZZER (Crescendo Alarm) NOTE: Alarm 1 and Alarm 2 have different buzzer sounds. You will be able to tell which alarm is going off by the sound that it makes. 1. ) Reconfirm the wake up time and alarm mode settings for the alarm you are using, Alarm 1, Alarm 2, or both alarms. 2. ) Set the ALARM selector switch for one or both alarms to the BUZZER position. [. . . ] To change the battery proceed as follows: 1. ) Purchase a replacement 3V lithium battery wherever batteries are sold. This will provide power to the SmartSet® computer memory while the original lithium battery is removed. 3. ) Turn the radio face up and use a small screwdriver to remove the screw securing the battery holder to the cabinet. BE CAREFUL NOT TO LOSE THIS SMALL SCREW! 4. ) Remove the original battery from the holder and insert the new battery into the holder the same way, observing the positive (+) direction. [. . . ]