User manual LASERLINE 291

[. . . ] GB 290i2/212/291/213 INSURANCE APPROVED ALARM/IMMOBILISER USER GUIDE ® CAR ALARM SYSTEMS ISUT291-213UK. p65 1 11/05/2006, 18. 53 These systems are manufactured from the highest quality components to ensure a long trouble free operating life and comply with the British insurance industry's criteria for vehicle security for Category 1 product - 291/213 and Category 2 à 1 (L2 à 1) product ­ 290i2/212, as evaluated by Thatcham (MIRRC). Note: Category 2 à 1 (L2 à 1) product ­ 290i2/212 alarm system is only to be fitted in conjunction with a Category 2 (L2) immobiliser to obtain Category 1 status for the vehicle security. These instructions are intended to familiarise you with their very simple operation. ** Vehicle dependent. NO DANGER FOR USER DUE TO THE RADIOFREQUENCY EXPOSURE! WARNING ALARMS MUST NOT BE STEAM CLEANED OR PRESSURE WASHED. [. . . ] COMFORT FUNCTION* (only for vehicle equipped with Comfort Closing of locking/ windows/roof**) For cars equipped with Comfort Closing function, the windows can be closed just by pressing and holding button `A' of the remote control. When the windows have reached the required height, release button `A' and the windows will stop immediately. In the same way, if button `A' is pressed and held while disarming the alarm, the power locks will open and the windows will open automatically**. CASUAL RE-ARMING* On your return to the vehicle, if you disarm the system but do not enter the vehicle (doors/bonnet/ boot) within 30 seconds, the alarm will automatically re-arm itself (reactivating the power locking system but not the accessory output). Useful if you accidentally disarm the alarm from a distance without knowing. This function is cancelled if you enter the vehicle (doors/bonnet/boot) within 30 seconds from when the alarm is disarmed. PASSIVE ARMING* This function allows the alarm to be armed automatically without using the remote control: Turn off the ignition key and exit the vehicle. 10 seconds after the last door is closed/or 10 seconds after the courtesy lights go out the alarm will arm (the function does not activate the power locking system and the accessory output). SAFETY LOCKING* This function automatically closes the power locking system in the following situation: Disarm the alarm with the remote control or electronic key. Enter vehicle and only after having closed all the protected areas (doors/boot/bonnet), turn the ignition key ON. The power locking system will automatically lock the doors after 5 seconds. The doors will unlock automatically when the ignition key is turned OFF. ISUT291-213UK. p65 12 11/05/2006, 18. 53 IMPORTANT NOTE: Only to be used if the car is equipped with an original " crash sensor" (inertia switch) power locking system that is activated if an accident occurs. will be not be held responsible if users do not comply with this note. Enter the vehicle and make sure that all doors/ bonnet/boot are closed. Turn the ignition key ON; within 5 seconds press button "B" of the remote control once. At the same time that you press button "B", you will hear a brief audible tone to confirm the programming. Now the siren sound is temporarily excluded and if an alarm condition occurs, only the direction indicator lights will flash. This function may be necessary in hospital parking areas, ferries, skiing resorts etc. The function will be reset the next time the alarm is armed using the remote control or an electronic key. ATTENTION: excluding the siren does not deactivate the additional siren/vehicle horn/paging system and the panic function. FLAT INTERNAL BATTERY POWER SUPPLY SIGNAL (290i2/291 only) If your alarm system is equipped with an internal battery, it can automatically check the battery charge and charging circuit. In case of a malfunction, the system communicates the problem to you through the "Alarm auto-diagnostics" function by flashing the LED 10 times. [. . . ] Damage caused by external electrical source or from abnormal variation or failure of power supply. Failure caused by installation of accessories not approved by the product manufacturer. Replacement of defective parts within the guarantee period does not include consumable parts or include labour. If product is repaired by a non authorised installer the product will cease to be covered by the warranty. [. . . ]