User manual LASERLINE 278UK

[. . . ] GB 270UK/278UK INSURANCE APPROVED ALARM (ORIGINAL REMOTE CONTROL UPGRADE) USER GUIDE ® CAR ALARM SYSTEMS ISUT270-278UK. p65 1 12/05/2006, 10. 24 270UK/278UK COMPACT ALARM SYSTEM FOR ALL CARS/LIGHT COMMERCIAL VEHICLES This system is manufactured from the highest quality components to ensure a long trouble free operating life and comply with the British insurance industry's criteria for vehicle security for Category 2 à 1 (L2 à 1) (AFTERMARKET SYSTEMS) [Utilising the original equipment remote tested to Issue 2 Criteria] product, as evaluated by Thatcham (MIRRC). Note: Category 2 à 1 (L2 à 1) product ­ 270/278 alarm system is only to be fitted in conjunction with a Category 2 (L2) immobiliser to obtain Category 1 status for the vehicle security. The 270/278 Category 2 - 1 alarm is for vehicles equipped with a 12v negative earth electrical system. These instructions are intended to familiarise you with their very simple operation. THIS PRODUCT MUST BE INSTALLED BY SKILLED AND QUALIFIED PERSONNEL WARNING ALARMS MUST NOT BE STEAM CLEANED OR PRESSURE WASHED. [. . . ] Z to toggle OFF the acoustic tones: remove the electronic key after the LED has flashed three in succession, accompanied by three acoustic tones. To toggle ON the acoustic tones: remove the electronic key after the LED has flashed three in succession (no acoustic tones). Ultrasonic and Siren exclusion will work normally after you disarm the alarm. Disabling the ultrasonic detector causes the optional window closing/optional sensor to be disabled and therefore all the associated functions. 8 - GARAGE FUNCTION This function allows the alarm system to be excluded temporarily, in order to let you leave the vehicle in a workshop for repairs or maintenance. When you receive the vehicle back, you can exit this mode and restore the alarm back to its normal functions. To enable garage function: OE insert and hold an electronic key into the receptacle socket; · Z wait until the LED flashes four times in succession, accompanied by four acoustic tones; continue to hold the electronic key in the receptacle socket for a further 3 seconds until garage mode is signalled by a short flash of the direction indicator lights and a short acoustic tone; pag. 11 ISUT270-278UK. p65 11 12/05/2006, 10. 24 ENGLISH · now remove the electronic key. With garage function enabled the alarm will flash the red LED in the receptacle every 15 seconds to indicate garage mode. If the optional immobilisation relay is fitted to the vehicle with the optional passive functions enabled, these function will be disabled allowing the vehicle to be driven. To disable the garage function: OE turn on the vehicles ignition key and keep it turned on; · Z · insert an electronic key into the receptacle socket; the exit from the garage mode will be signalled by a long flash of the direction indicator lights and a long acoustic tone; remove the electronic key. 9 - DISARM USING YOUR EMERGENCY PIN CODE If your original remote control/electronic key does not work correctly or has been lost, to disarm the alarm system and enter the alarm into garage function (see section 8) you must insert the "emergency pin code" by doing the following: OE · Z With the alarm armed, activate the siren by opening the door on the driver's side; Enter the vehicle. The alarm will stop sounding after 30 seconds and then the LED installed on the dashboard will illuminate for 5 seconds. Within the 5 seconds, turn the ignition key ON and OFF for 1 second; The LED in the receptacle will start to flash and the alarm is ready to accept the Pin Code. Wait for the flashes corresponding to each digit of your Pin Code to be displayed, then turn the ignition key ON and OFF for 1 second only after the LED is off. 12 ISUT270-278UK. p65 12 12/05/2006, 10. 24 ENGLISH the pin code to be inserted is 5 6 0 5 4. 5 6 0 5 4 = = = = = Key LED Flashes Acoustic Tones Key On Key On Key On pause Key On pause Key On pause pause Key On Pin code entered correctly alarm enters garage function without accoustic tones or flashing the direction indicator lights Pin code entered incorrectly alarm will stay armed ALARM DISARMED Ignition Key On ALARM ARMED pag. 13 ISUT270-278UK. p65 13 12/05/2006, 10. 24 ENGLISH EXAMPLE: the pin code to be inserted is 5 6 0 5 4. After the fifth flash/acoustic tone has been completed and the LED has turned OFF, immediately turn ON the ignition key for 1 second. Turn the ignition OFF and after a pause, the LED/acoustic tones will start again for the next digit of the Pin Code; Second digit 6 - Wait 6 flashes/acoustic tones for the second digit. After the sixth flash/acoustic tone has been completed and the LED has turned OFF, immediately turn ON the ignition key for 1 second. Turn the ignition OFF and after a pause, the LED/acoustic tones will start again for the next digit of the Pin Code; Third digit 0 - For the 0 digit, the flashes/acoustic tones to be completed are 10. Continue until all the digits have been displayed and inputted correctly. If the code inserted is correct, the alarm will automatically disarm and enter garage function, without a short flash of the direction indicator lights and a short acoustic tone. If the code is incorrect, the alarm will stay armed and sound the siren if triggered again. [. . . ] CONSUMER SUMMARY All warranties are limited to the duration of this warranty. This is the complete warranty and no other express or implied warranty is valid. NOTE Manufacturer declines any responsibility for damage of the alarm/immobiliser and the vehicle electrical system due to WRONG INSTALLATION OR TAMPERING. LASERLINE SpA RESERVES THE RIGHT TO EFFECT CHANGES OF THE PRODUCT WITHOUT FURTHER NOTICE. pag. [. . . ]