User manual LA CROSSE TECHNOLOGY WS6118

[. . . ] Within 3 minutes, insert 2 x AA, IEC LR6, 1. 5V batteries into the Moonphase wall clock as indicated above (see "To install and replace batteries in the Moonphase wall clock" above). Once the batteries are in place, all segments of the LCD will light up briefly. Then the indoor and outdoor temperature - -. -° the time as 0:00, the date as 1/1, and weekday will C, be displayed. Do not press any buttons for 10 minutes The Moonphase wall clock will start receiving data from the transmitter. [. . . ] The range runs from 0 to -12 and then runs from 12 back to 0 in consecutive 1-hour interval. Press and release the SET key to enter the "Language Setting". LANGUAGE SETTING The weekdays can be displayed in LCD1 with the pre-set languages: German = d, English = US, French = F, and Spanish = E. Set the desired language for the weekday display in LCD1 by use of the + key. Press and release the SET key to enter the mode "Manual Time Setting". MANUAL TIME SETTING In case the Moonphase wall clock is not able to detect the DCF-signal (disturbances, transmitting distance, etc. ), the time can be manually set. Set the desired hours by pressing and releasing the + key followed by pressing the SET key. Press and release the SET key to move to the "Year Setting". YEAR SETTING The year can be selected sequentially from 2001 to 2029 and will then start over again (default setting 2006). Press and release the SET key to switch to the "Month Setting". MONTH SETTING 1. Press and release the SET key to move to the mode "Date Setting". 20 DAY SETTING 1. The digits for the day will start flashing on LCD2 (Default setting 1). For example, it is not possible to set the data 30 if the months of February is selected. Press and release the SET key to enter the "Weekday Setting". The weekday symbols will be displayed on LCD2 in the pre-set language and flashing. Press and release the SET key to enter the mode "12/24 Hours Time Display Setting". The "12h" or "24h" will start flashing in LCD1 (Default setting 24h). Press and release the SET key to enter the "ºC/ºF Temperature Setting". The characters "° or "° will start flashing on LCD1 (Default setting ° B y use of the C" F" C). + key select "° for temperature display in degrees Celsius or "° for degrees C" F" Fahrenheit. Press and release the SET key to exit the setting mode and switch back to the normal display mode. 2. 1. WEEKDAY SETTING 12/24 HOURS TIME DISPLAY SETTING ° OR ° TEMPERATURE SETTING C F 2. EXIT THE MANUAL SETTING MODES · · To return to the normal display mode from anywhere in manual setting mode simply press the SNZ key anytime. If no keys are pressed for about 15 seconds in setting mode, the Moonphase wall clock will automatically switch back to normal display mode. ALARM SETTING To enter into the alarm setting mode: 1. If the + key is held, the unit will increase by 5. 21 5. Press and release again the ALM key to exit the Alarm setting mode or wait for 15 seconds automatic timeout or press the SNZ key. Note: the alarme duration is about 85 seconds TO DEACTIVATE THE ALARM: Alarm icon (((·))) (ON) The alarm will be automatically ON when the alarm time is set. To deactivate the alarm (OFF), press and release once the ALM key in normal mode display. [. . . ] Please help in the preservation of the environment and return used batteries to an authorized depot. 26 LIABILITY DISCLAIMER · · · · · · · · · · · The electrical and electronic wastes contain hazardous substances. Disposal of electronic waste in wild country and/or in unauthorized grounds strongly damages the environment Please contact your local or/and regional authorities to retrieve the addresses of legal dumping grounds with selective collection All electronic instruments must from now on be recycled. User shall take an active part in the reuse, recycling and recovery of the electrical and electronic waste. The unrestricted disposal of electronic waste may do harm on public health and the quality of environment. [. . . ]