User manual LA CROSSE TECHNOLOGY WS-7038UF

[. . . ] If no buttons are pressed, the digits will stop flashing after 50 seconds. To enter the programming mode (when not automatically entered) hold down the RAIN/SET button for 2 seconds--the minute digits will flash. The Program Mode is laid out in a manner that allows you to program each function separately, or you can follow the instructions entirely to program the Rain Monitor. Complete programming is usually done for the initial set-up, and will require you to skip step 1 of programming sections II through VI. [. . . ] The information that is displayed in column "0" is renewed every Monday at midnight, and the information contained in the columns is shifted to the left. If "MONTHLY" is selected, the graph will display the rainfall history for the past 6 months. The information displayed in column "0" is renewed on the first day of every month, at midnight. The information contained in the columns is shifted to the left. 7 II) NUMERICAL REPRESENTATION OF THE BAR GRAPH The bar graph displays the columns sequentially from "0" to "6" until all columns are showing. It is possible to read each column one at a time, simultaneously displaying the numeric measurement for that column above the bar graph. For example, the weekly rainfall total from 3 weeks ago may be viewed. Also, the numeric data from each column will correspond to the preveouly selected history ("DAILY, " "WEEKLY, " or "MONTHLY"). The numeric data from column "0" should appear at the top of the LCD screen, with the "RAINFALL" icon displayed above the data. Press the HISTORY/+ button again, column "1" will be highlighted, and the numeric data will be displayed above the bar graph. Continue to press the HISTORY/+ button until the data from each column (0 through 6) has been displayed. Pressing the HISTORY/+ button once more, after viewing the data from column 6, will exit this mode--returning to normal operation. 2. 4. III) MANUAL RESET OF THE RAIN MULTIPLICATOR Note: The rain multiplicator is the amount of rain needed to tip the teeter-totter bucket (inside the rain gauge). The multiplicator is preset to a value of "105" (0. 0105 inches per tip); this number produces the most accurate rainfall measurement. There is no need to manually set this number unless it has been changed. This will reset the 1-hour rainfall total, but the bar graph and other totals will remain. During the brief 2 seconds that the LCD screen lights up, hold down the HISTORY/+ button, until "105" appears in the LCD (the "5" will be flashing). If the multiplicator is not 105; use the HISTORY/+ button to to change the last digit to a 5. Press the HISTORY/+ button to change the middle digit, and press the RAIN/SET button to confirm and shift to the first digit. Press the RAIN/SET button to exit the Rain Multiplicator mode, and to enter the normal mode. Follow Program Mode for set-up proceedures. 4. 5. 6. 8 IV) COMPLETE RESETTING OF PRECIPITATION DATA Note: The rain data held by the bar chart and other rain totals (excluding the 1-hour total) will be stored and displayed again, even after the batteries have been removed. Therefore it is necessary to apply the following instructions to reset the bar chart and other totals, if desired. 1) Enter the Rain Multiplicator mode as instructed in steps 1 through 3 of the Manual Reset of the Rain Multiplicator section above. [. . . ] The owner must pay any shipping charges incurred in getting your La Crosse Technology, Ltd product to a La Crosse Technology, Ltd authorized service center. La Crosse Technology, Ltd will pay ground return shipping charges to the owner of the product to a USA address only. Your La Crosse Technology, Ltd warranty covers all defects in material and workmanship with the following specified exceptions: (1) damage caused by accident, unreasonable use or neglect (including the lack of reasonable and necessary maintenance); (2) damage occurring during shipment (claims must be presented to the carrier); (3) damage to, or deterioration of, any accessory or decorative surface; (4) damage resulting from failure to follow instructions contained in your owner's manual; (5) damage resulting from the performance of repairs or alterations by someone other than an authorized La Crosse Technology, Ltd authorized service center; (6) units used for other than home use (7) applications and uses that this product was not intended or (8) the products inability to receive a signal due to any source of interference. . This warranty covers only actual defects within the product itself, and does not cover the cost of installation or removal from a fixed installation, normal set-up or adjustments, claims based on misrepresentation by the seller or performance variations resulting from installation-related circumstances. [. . . ]