User manual KENWOOD KRF-V6400D

[. . . ] Using the remote control without completely understanding its design and how to switch the operation modes may result in incorrect operations. B60-4557-00 (EN) Before applying the power Units are designed for operation as follows. Caution : Read this page carefully to ensure safe operation. 2 Unpacking Unpack the unit carefully and make sure that all accessories are put aside so they will not be lost. If your unit is damaged or fails to operate, notify your dealer immediately. If your unit was shipped to you directly, notify the shipping company without delay. Only the consignee (the person or company receiving the unit) can file a claim against the carrier for shipping damage. [. . . ] In such a case, change the location of the system installation to prevent malfunction. Other 6m Operations · Insert two AA-size (R06) batteries as indicated by the polarity markings. Preparations Normal playback 10 ON/STANDBY SPEAKERS A B INPUT SELECTOR POWER MULTI CONTROL VOLUME CONTROL BALANCE Selecting the speaker system Press the SPEAKERS A or B key to select the speaker system to be used. : Sound from the speakers connected to the SPEAKERS A terminals on the rear panel. B ON : Sound from the speakers connected to the SPEAKERS B terminals on the rear panel. A+B ON : Sound from both the speakers connected to the SPEAKERS A and B terminals on the rear panel. A ON Preparations Operations Other SOUND SOURCE DIRECT AUTO POWER VOLUME UP, DOWN SOUND BASS BOOST S. DIRECT MUTE BALANCE MULTI CONTROL INPUT SELECTOR The indicator for the speakers you want to use should be lit. SP. A B Listening to a source component Preparing for playback Some preparatory steps are needed before starting playback. 1Use the input selector (INPUT SELECTOR) to select the source you want to listen to. The input sources change as shown below: Selecting a source using the INPUT SELECTOR 1 2 3 4 5 TUNER (frequency display) "CD" "TAPE 1" or "MD" "PHONO" "AUX" Turning on the receiver 1 Turn on the POWER key to ON. STANDBY ( Selecting MD/TAPE 1 (Main unit only) Select the source name corresponding to the component connected to the MD/TAPE1 jacks. To change the source name associated with the MD/TAPE1 jacks to "MD", follow the steps below: 1 Use the INPUT SELECTOR knob to select "TAPE 1". · To return to the original indication, repeat the above procedure. · When selecting an input source by using the remote control , press the desired input selector key. 2 Start playback on the cassette deck connected to the MD/TAPE1 jacks and start recording on the cassette deck connected to the TAPE2/MONITOR jacks. · To copy tapes using a double cassette deck, refer to the instruction manual of the double cassette deck. TAPE 2/MONI FW INPUT -6 · The adjustment mode is displayed for approximately 8 seconds. · The input level may be adjusted to any one of 2 settings: 0 and -6. (The initial setting is 0. ) 4 Press the SOUND key to return to the input indication. Listening to radio broadcasts Tuning (non-RDS) radio stations Radio stations can be classified into RDS (Radio Data System) stations and other stations. To listen to or store RDS stations in the preset memory, see the section entitled, "Using RDS". TA/NEWS PTY DISPLAY Using RDS (Radio Data System) RDS is a system that transmits useful information (in the form of digital data) for FM broadcasts along with the broadcast signal. Tuners and receivers designed for RDS reception can extract the information from the broadcast signal for use with various functions, such as automatic display of the station name. 13 PTY (Program TYpe identification) Search ^ Automatically tunes to a station that is currently broadcasting the specified program type (genre). BAND MEMORY INPUT SELECTOR MULTI CONTROL AUTO 1~0, +10 VOLUME UP, DOWN BAND AUTO 4 P. CALL ¢ MULTI CONTROL INPUT SELECTOR DISPLAY TA/NEWS ^ EON (Enhanced Other Network) reservation Sets the tuner to automatically switch to stations broadcasting one of two types of programs, even though you are listening to another station. The tuner returns to the original station when the broadcast of the selected program ends. PS (Program Service name) Display Automatically displays the station name transmitted by the RDS station. DIMMER PTY 1Use the input selector (INPUT SELECTOR) to select the tuner. 2Use the BAND key to select the desired broadcast band. Each press switches the band as follows: 1 FM 2 AM "FM" or "AM" indicator SP. A B FM AM $ RDS Auto Memory function Automatically selects and stores up to 30 RDS stations in the preset memory. If fewer than 30 RDS stations have been stored in the preset memory, regular FM stations will be stored in the remaining places. Radio Text function Displays the radio text data transmitted by some RDS stations when you press the DISPLAY key. There is no display if no text data was transmitted. method. Each press switches the tuning method as follows: 1 AUTO lit (auto tuning) 2 AUTO not lit (manual tuning) STEREO . )) AUTO MHz The "RDS" indicator lights up when an RDS broadcast (signal) is received. SP. [. . . ] · The remote control unit is too far away from the main system, controlling angle is too large, or there is an obstacle between the receiver and the remote. · The audio cords and system control cords are not connected properly. · An attempt is made to play a tape which is being recorded in the cassette deck. 9 · Operate the remote control unit within the controllable range. [. . . ]