User manual KENWOOD KDC-X592
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual KENWOOD KDC-X592. We hope that this KENWOOD KDC-X592 user guide will be useful to you.
Manual abstract: user guide KENWOOD KDC-X592
Detailed instructions for use are in the User's Guide.
[. . . ] KDC-X592 KDC-MP538U
CD-RECEIVER
INSTRUCTION MANUAL
AMPLI-TUNER LECTEUR DE CD
MODE D’EMPLOI
REPRODUCTOR DE DISCOS COMPACTOS RECEPTOR DE FM/AM
MANUAL DE INSTRUCCIONES
Take the time to read through this instruction manual. Familiarity with installation and operation procedures will help you obtain the best performance from your new CD-receiver. For your records
Record the serial number, found on the back of the unit, in the spaces designated on the warranty card, and in the space provided below. Refer to the model and serial numbers whenever you call upon your Kenwood dealer for information or service on the product. [. . . ] 2 Enter Detail adjustment mode of Audio
Control Press the [AUD] knob for at least 1 second. 5 Exit the Detail Audio Control mode
Press the [AUD] knob for at least 1 second.
• When you set the Bass Extend to ON, low frequency response is extended by 20%. You can exit the Audio Control mode at anytime by pressing any button except for [AUD] knob, [0] and [ATT] button. Speaker Setting
Range Through/40*1/ 60*1/80/100/ 120/150/180/220*1 Hz Through/40*1/ 60*1/80/100/ 120/150/180/220*1 Hz 50*1/60/80/100*1/120/ Through Hz Reverse (180°)/ Normal (0°) –8 — ±0 (AUX: -8— +8) OFF/ON OFF/ON Fine-tuning so that the System Q value is optimal when setting the speaker type as follows; Speaker type OFF For 5 & 4 in.
• Volume offset: Sets each source’s volume as a difference from the basic volume. (Only the low tone is compensated for when the tuner is selected as a source. - Adjust the volume of Rear channel by <Audio Control> (page 15) or [5]/[∞] button on the remote control (page 20). 1 Select the source to adjust
For how to select source item, refer to <Power/ Source Select button> of <Basic Operation> (page 4). audio Preset Recall
Recalling the sound setup registered by <Audio Preset Memory> (page 17). 1 Setup Sound Control
Refer to the following operations to setup the Sound Control. - <Audio Control> (page 15) - <Audio Setup> (page 16)
1 Select the source
For how to select source item, refer to <Power/ Source Select button> of <Basic Operation> (page 4). 2 Select Audio Preset item during Menu
mode (Other than Standby mode) Select the “Audio Preset” display. for how to select Function Control items , refer to <Function Control> (page 6). 2 Select Audio Preset item during Menu
mode (Other than Standby mode) Select the “Audio Preset” display. for how to select Function Control items , refer to <Function Control> (page 6). 3 Enter Audio Preset mode
Press the Control knob for at least 1 second. 3 Enter Audio Preset mode
Press the Control knob for at least 1 second. 5 Determine whether to recall the Audio Preset
Press the Control knob. 5 Determine whether to put the Audio Preset in
the memory Press the Control knob. 6 Recall the Audio Preset
Turn the Control knob to select “YES”, and then press the Control knob. 6 Put the Audio Preset in the memory
Turn the Control knob to select “YES”, and then press the Control knob. [. . . ] Before calling service, first check the following table for possible problems. <Audio Setup> (page 16) • Cannot select the output destination of the subsource in the Dual zone. The key illumination effect brought about in conjunction with the sound volume is small. The key illumination effect may be insufficient depending on the sound volume and sound quality. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE KENWOOD KDC-X592
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual KENWOOD KDC-X592 will begin.