User manual JRC NSVS875

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual JRC NSVS875. We hope that this JRC NSVS875 user guide will be useful to you.


JRC NSVS875 : Download the complete user guide (172 Ko)

Manual abstract: user guide JRC NSVS875

Detailed instructions for use are in the User's Guide.

[. . . ] 2004 JRC SAW FILTER NSVS875 Application 433. 92MHz R. K. E. Electrical Specification: (Table 1) The device characteristics are measured in the circuit shown in Fig. 1. Electrical Specifications Item Input and Output Impedance Nominal Center Frequency (f0) Insertion Loss f0·} Response Variation f0·} Input and Output VSWR f0·} Out of Band Rejection f0·} (Relative to Through Level) f0·} Spec. [. . . ] It might not be satisfied with electrical specification without operating temperature range. When it is used less than -35ºC or more than +85ºC, it might be a cause of degradation or destruction of the component. Even if it endures during a short time, it causes degradation of qualification. When soldering iron is used, solder with the temperature at the tip of soldering iron: 350ºC max. , the time of soldering: 10 seconds max. , the power of soldering iron: 30W max. . Notice that the allowed time of soldering with soldering iron is accumulated time, when soldering is repeated. As rapid temperature change for cleaning after reflow soldering might be a cause of destruction clean this component after confirming that temperature of this component goes down to room temperature. Confirm that there are not any influence for qualification to this component in mounting on PCB when this component is cleaned. As it might be a cause of degradation of destruction to apply static electricity to this component, do not apply static electricity or excessive voltage while assembling and measuring. This specification specifies the quality of this component as a single unit. Make sure that this component is evaluated and confirmed against this specification when it is mounted to your products. [. . . ] 2004 IN 50 O *27nH 11 10 , X , W , U , V OUT 50 O 39pF 12 SAW , P , Q , , T R *27nH , S 33pF 0 S21 FREQUENCY CHARACTERISTICS *murata LQW18A series 0 Insertion Loss [dB] 20 2 (1) 13. 30±0. 20 40 (a) (b) (C) (1. 26±0. 13) (2) 4 60 6 80 100 CH1 : center 433. 92 span 30 CH2 : center 433. 92 span 30 J4Y1 VS971 S11 6. 5±0. 20 8 10 (3) S22 (R0. 3) [4×] Marking (1) Manufacture's Mark (2) Lot Number (a) Year 2. 0 max. (b) Month *Oct. --- X Nov. --- Y Dec. --- Z (0. 76) VSWR S11 11 9 7 5 3 1 418. 9 (2. 54) (2. 54) S22 11 9 (c) Date 1 --- 0 -9 10 -19 --- 1 20 -31 --- 2 (3) Part Number Mark VSWR 7 5 3 (2. 54±0. 15) 448. 9 Frequency [MHz] (1. 4) [12×] Frequency [MHz] Pin No. Connection 1 2 3 4 5 6 7 8 448. 9 1 418. 9 GND(PKG) GND(PKG) GND(PKG) GND(PKG) OUT/IN GND(signal) GND(PKG) GND(PKG) GND(PKG) GND(PKG) IN/OUT GND(signal) 0 InsertionLoss [dB] 20 40 60 80 100 12 1 2 3 4 5 (2. 54±0. 15) 11 10 9 8 7 6 [12 ×] S21 (0. 8) 9 10 11 12 (R0. 3) 0. 3 [12×] 2000 Fig. 2 Package dimensions(in mm) Frequency [MHz] Insertion Loss [dB] Fig. 1 Measuring circuit [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE JRC NSVS875




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual JRC NSVS875 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.