User manual JRC NSVS1196

[. . . ] 2008 JRC SAW RESONATOR NSVS1196 Application 433. 92MHz Resonator Electrical Specification: (Table 1) The device characteristics are measured in the circuit shown in Fig. 2. Electrical Specifications Item Center frequency Absolute frequency Tolerance from 433. 92MHz Insertion Loss @Minimum Loss Temperature Stability Turnover Temperature Temperature Coefficient DC Insulation Resistance between any two terminals RF Equivalent Motional Resistance (RM) RLC Model (fig. 1) Motional Inductance (LM) Motional Capacitance (CM) Shunt Static Capacitance (C0) Specification ±50kHz max. [. . . ] 5 3) [ 4 x] 2 3 4 5 6 Fig. 2 Package dimensions (in mm) 3. 8 0. 93 2. 2 1. 15 3. 8 0. 6 1. 15 0. 93 Fig. 3 Desirable land area (in mm) NSVS1196 Oct. It might not be satisfied with electrical specification without operating temperature range. When it is used less than -40ºC or more than +85ºC, it might be a cause of degradation or destruction of the component. Even if it endures during a short time, it causes degradation of qualification. When soldering iron is used, solder with the temperature at the tip of soldering iron: 350ºC max. , the time of soldering: 10 seconds max. , the power of soldering iron: 30W max. . Notice that the allowed time of soldering with soldering iron is accumulated time, when soldering is repeated. As rapid temperature change for cleaning after reflow soldering might be a cause of destruction clean this component after confirming that temperature of this component goes down to room temperature. Confirm that there are not any influence for qualification to this component in mounting on PCB when this component is cleaned. As it might be a cause of degradation of destruction to apply static electricity to this component, do not apply static electricity or excessive voltage while assembling and measuring. This specification specifies the quality of this component as a single unit. [. . . ] 2008 IN 50 O *27nH 11 10 , X , W , U , V OUT 50 O 39pF 12 SAW , P , Q , , T R *27nH , S 33pF 0 S21 FREQUENCY CHARACTERISTICS *murata LQW18A series 0 Insertion Loss [dB] 6 2 (1) 13. 30±0. 20 12 (a) (b) (C) (1. 26±0. 13) (2) 4 18 6 24 30 CH1 : center 433. 92 span 1 CH2 : center 433. 92 span 1 J4Y1 VS971 S11 6. 5±0. 20 8 10 (3) S22 (R0. 3) [4×] Marking (1) Manufacture's Mark (2) Lot Number (a) Year 2. 0 max. (b) Month *Oct. --- X Nov. --- Y Dec. --- Z (c) Date (0. 76) (2. 54) (2. 54) 1 --- 0 -9 10 -19 --- 1 20 -31 --- 2 S11 VSWR VSWR 11 11 S22 (2. 54±0. 15) (3) Part Number Mark (1. 4) 9 Pin No. Connection 1 2 GND(PKG) GND(PKG) GND(PKG) GND(PKG) OUT/IN GND(signal) GND(PKG) GND(PKG) GND(PKG) IN/OUT GND(signal) 9 7 5 3 [12×] 7 (0. 8) 5 [12 ×] 3 4 5 6 12 (2. 54±0. 15) 1 433. 4 1 2 433. 9 Frequency [MHz] 3 434. 4 3 4 5 433. 9 Frequency [MHz] 1 433. 4 7434. 4 GND(PKG) 8 9 10 11 12 11 10 9 8 7 6 (R0. 3) [12×] Fig. 2 Package dimensions(in mm) Insertion Loss [dB] Fig. 1 Measuring circuit [. . . ]