User manual JRC NSVS1058

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual JRC NSVS1058. We hope that this JRC NSVS1058 user guide will be useful to you.


JRC NSVS1058 : Download the complete user guide (116 Ko)

Manual abstract: user guide JRC NSVS1058

Detailed instructions for use are in the User's Guide.

[. . . ] 2004 JRC SAW FILTER NSVS1058 Application 1575. 42MHz GPS(Low Loss Type) Electrical Specification: (Table 1) The device characteristics are measured in the circuit shown in Fig. 1. Input and Output Impedance 50 Nominal Center Frequency (f0) 1575. 42MHz Insertion Loss 1574. 42~1576. 42MHz 1. 6dB max. [. . . ] 1 2 3 4 Connection GND IN/OUT GND OUT/IN 2. 8 1. 03 1. 03 Fig. 3 Desirable land area (in mm) NSVS1058 Oct. It might not be satisfied with electrical specification without operating temperature range. When it is used less than -40ºC or more than +85ºC, it might be a cause of degradation or destruction of the component. Even if it endures during a short time, it causes degradation of qualification. When soldering iron is used, solder with the temperature at the tip of soldering iron: 350ºC max. , the time of soldering: 10 seconds max. , the power of soldering iron: 30W max. . Notice that the allowed time of soldering with soldering iron is accumulated time, when soldering is repeated. As rapid temperature change for cleaning after reflow soldering might be a cause of destruction clean this component after confirming that temperature of this component goes down to room temperature. Confirm that there are not any influence for qualification to this component in mounting on PCB when this component is cleaned. As it might be a cause of degradation of destruction to apply static electricity to this component, do not apply static electricity or excessive voltage while assembling and measuring. This specification specifies the quality of this component as a single unit. [. . . ] 2004 IN 50 O *27nH 11 10 , X , W , U , V OUT 50 O 39pF 12 SAW , P , Q , , T R *27nH , S 0 S21 33pF FREQUENCY CHARACTERISTICS 1 *murata LQW18A series 0 1 Insertion Loss [dB] 10 2 2 : 1576. 42 [MHz] 1. 08 [dB] 3 : 1500 [MHz] 63. 86 [dB] 2 (1) 13. 30±0. 20 20 (a) (b) (C) (1. 26±0. 13) 4 : 1675. 42 [MHz] 24. 16 [dB] 4 (2) 4 30 6 40 50 CH1 : center 1575. 42 span 200 3 CH2 : center 1575. 42 span 200 J4Y1 VS971 S11 1 6. 5±0. 20 8 10 4 (3) S22 (R0. 3) [4×] Marking (1) Manufacture's Mark (2) Lot Number 1 2 (a) Year (b) Month *Oct. --- X Nov. --- Y 2. 0 max. 2 3 4 3 4 (c) Date Dec. --- Z S11 (0. 76) 11 9 3 (2. 54) (2. 54) 11 S22 3 1 --- 0 -9 10 -19 --- 1 20 -31 --- 2 VSWR VSWR 4 9 7 5 3 7 5 3 1 1475. 4 1 (2. 54±0. 15) 2 Frequency [MHz] 4 (3) Part Number Mark 1 1675. 4 1475. 4 (1. 4) [12×] 1 2 Pin No. Connection 1 2 3 4 5 6 7 8 [12 ×] 1675. 4 GND(PKG) GND(PKG) Frequency [MHz] (0. 8) 0 S21 1 2 3 4 GND(PKG) GND(PKG) OUT/IN GND(signal) GND(PKG) GND(PKG) GND(PKG) GND(PKG) IN/OUT GND(signal) InsertionLoss [dB] 10 12 20 5 (2. 54±0. 15) 30 11 10 40 50 0 9 8 7 6 9 10 11 12 (R0. 3) [12×] 3000 Frequency [MHz] Fig. 2 Package dimensions(in mm) Japan Radio Co. , Ltd. Insertion Loss [dB] 2 Fig. 1 Measuring circuit 1 : 1574. 42 [MHz] 1. 07 [dB] [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE JRC NSVS1058




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual JRC NSVS1058 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.