User manual ISOTEK SIGMAS

[. . . ] Our circuit designs are extensively `field' tested before coming to market so we can guarantee the widest compatibility with third party products. Within the market of premium audio it is vital to offer exceptional performance and value for money. Products must be made to the highest of standards, be reliable and attractive. A manufacturer must offer exceptional service, dealer training, support and undertake the very best in promotion design and literature. [. . . ] Dolding all rights reserved. ® The Combined max current should not exceed 6A HIGH VOLTAGE No user serviceable parts inside Refer to authorised personnel for servicing Serial No. June 2006 B. The product All components used within Sigmas are of the highest grade or designed by IsoTek and manufactured to MOD / Aerospace specification and tollerance. The unit is also fully star earthed. Weight loading Safety In the interest of safety the unit should be placed upon its own dedicated shelf on an audio grade equipment rack. Ensure that a minimum distance of 50mm is allowed around the unit for sufficient ventilation. Ventilation should not be impeded by covering the ventilation openings with items such as newspapers, table-cloths, curtains, etc. No naked flame sources, such as lighted candles should be placed on the unit. The unit may be placed on top of or under other pieces of equipment, but do not exceed a maximum weight loading of 20kg. If you have to locate the unit on the floor we strongly recommend you do not place the unit near heat sources, such as radiators or air ducts. The unit should not be placed in areas which could exceed 25 degrees, for example near vacuum tube amplifiers. Good air circulation is essential to prevent heat build up within the chassis. Do not place the Sigmas on a soft surface, for example a rug or carpet, which could block the ventilation intakes on the underside of the unit. The apparatus must not be exposed to dripping or splashing and no objects filled with liquids, such as vases should be placed on top. Should either of these events happen immediately switch off the unit at the wall socket, wait for at least one minute, unplug all other cables and return it to your authorised IsoTek dealer for a full service. !20Kg 100 - 240V ~ 16A 50/60Hz Total: 16A 1600 - 3840VA Total: 6A 600 - 1440VA The Combined max current should not exceed 16A IsoTek is designed & hand made in England · www. isoteksystems. com · ©2005 K. Dolding all rights reserved. ® The Combined max current should not exceed 6A HIGH VOLTAGE No user serviceable parts inside Refer to authorised personnel for servicing Serial No. June 2006 C. Installation Placement Ideally the unit should be placed upon its own dedicated shelf of an audio grade equipment rack. If this is not possible the unit may be placed on top of or under other pieces of equipment to a maximum weight limit of 20kg. If you have to locate the unit on the floor or in any other location please refer to the safety section of this manual. Once the Sigmas is placed connect the unit to a mains wall socket, with the high quality power cable provided. The apparatus must be connected to an earthed mains socket outlet. Rear elevation of the unit Equipment coupling Switch on Professional 16Amp Neutrik inlet Dedicated earth post 2 High power high quality outputs 4 Medium power high quality outputs With Sigmas facing you turn on the right thermo-magnetic fuse (located under the chassis), this illuminates the right LED. Then turn on the left thermo-magnetic fuse, again the left LED will turn on. Turn off all equipment you wish to have a clean mains supply, unplug the cables relating to these from the wall socket or redundant distribution block you may have been using and plug these into the rear sockets of the Sigmas. [. . . ] Number of outlets: Type of outlets: Standard mains inlet: 6 UK, EU, and US unswitched 16Amp Neutrik Powercon 100 - 240V 16Amps 3680W 1760W 18400W 6Amps 1380W 660W Front & rear elevation Mains voltage: High current outlets (electronic fused) Watts at 230V Watts at 110V Maximum transient capability (high current, 230V) Medium current (electronic fused) Watts at 230V Watts at 110V Dimensions: Weight: 444mm x 85mm x 310mm (WxHxD) 9. 5Kg 100 - 240V ~ 16A 50/60Hz Total: 16A 1600 - 3840VA Total: 6A 600 - 1440VA Please note, the information given in this document is correct at the time of print. Small production changes in the course of improvement through our ongoing research and development policy may arise. If clarification of any point is required please refer to your local authorised IsoTek dealer or visit www. isoteksystems. com where you can download the very latest information. HIGH VOLTAGE No user serviceable parts inside Refer to authorised personnel for servicing The Combined max current should not exceed 16A IsoTek is designed & hand made in England · www. isoteksystems. com · ©2005 K. Dolding all rights reserved. ® The Combined max current should not exceed 6A Serial No. March 2004 F. [. . . ]