User manual IOGEAR GWAV8141K INSTALLATION

[. . . ] Installation Guide Wireless HD Kit GWAV8141K Table of Contents Package Contents Overview Wall Mount Installation Remote Control Selecting Specific Ports LED Indication IR Blast IR Extender Video Format Support Audio Format Support Connection Between the Transmitter Unit and Receiver Unit Factory Reset Firmware Upgrade / Configuration Update Streaming Mode FCC Statement CE Compliance Limited Warranty Contact 4 5 7 8 12 14 14 15 15 15 15 16 16 17 17 17 17 18 18 3 Package Contents 1 x Wireless HD Transmitter 1 x Wireless HD Receiver 1 x Remote Control 2 x Wireless HD Stand 1 x Component to VGA Adapter 1 x IR Blast 2 x Power Adapter 1 x Installation Guide 1 x Warranty Card 4 Overview Transmitter Unit Front View 1. DC Power Jack 8 1 9 2 10 3 4 11 12 5 13 6 7 14 15 *Note: For the audio part of a Component media source, please use the PC Audio Input Port with a 3. 5mm to RCA Cable (Not included and sold separately ­ IOGEAR Part No: G2LMMRCA006). [. . . ] Check to your transmitter unit is switched to the correct port for your specific media source. Please make sure the display supports the resolution that the media source is streaming at. For example, if you are using a 720p HD display to play a full 1080p content, you would need to downscale the source's resolution to 720p to match the display. 11 Remote Control 1 POWER INFO TRANSMITTER 4 HDMI1 RECEIVER HDMI1 HDMI HDMI2 HDMI2 2 5 COMP PC PC AV VIDEO OUT AV VIDEO IN AV AUDIO IN 3 LAN WiFi CH 1 WiFi CH 2 6 1 POWER ON · · If the transmitter unit and receiver unit are powered off with the Power/Link LED on, press the power button will turn on both transmitter unit and receiver unit simultaneously If the transmitter unit and receiver unit are powered off with the Power/Link LED off, you need to press the power button to turn on the transmitter unit and receiver unit individually If the transmitter unit and receiver unit are powered on with the Power/Link LED on, press the power button will turn both transmitter unit and receiver unit off simultaneously with the Power/Link LED staying on If the transmitter unit and receiver unit are powered on with the Power/Link LED on, press and hold the power button for 6 seconds will turn both transmitter unit and receiver unit off simultaneously with the Power/Link LED off If the transmitter unit and receiver unit are powered on with the Power/Link LED flashing, you would need to power off the transmitter unit and receiver unit individually Press to select HDMI as the output Press to select Component as the output Press to select Composite as the output OFF · · · 2 Receiver unit HDMI Component AV 3 LAN Press and hold the LAN button for 6 seconds to change the connection to Wired Mode 12 4 INFO Press to display information* of the transmitter unit, receiver unit and display: Transmitter unit** · WiFi Channel · Firmware Version · Video/Audio Input Receiver unit · Connection · Firmware Version · Video Output · Display Resolution · WiFi Reception (1 to 5, 1 being weakest and 5 being strongest) Display Resolutions that the display can support *Note: The display information will disappear automatically after 20 seconds **Note: The transmitter unit's information will only be displayed if the connection between the transmitter unit and receiver unit has been established 5 Transmitter Unit HDMI1 Video HDMI1 Audio HDMI2 Video HDMI2 Audio AV Video AV Audio PC Video PC Audio HDMI1 Audio HDMI2 Audio Press to select HDMI1 as the video input Press to switch back to HDMI1 as the audio input Press to select HDMI2 as the video input Press to switch back to HDMI2 as the audio input Press to select Composite as the video input Press to select Composite as the audio input Press to select VGA/Component as the video input Press to select PC Audio-In as the audio input Press to switch back to the HDMI1 as the audio input Press to switch back to the HDMI2 as the audio input Note1: If you have switched to a specific video port via remote control without specifying the audio port on the transmitter unit, by default, it will also switch the audio to that specific port. Note2: Independent audio switching is only allowed for AV Audio and PC Audio. 6 WiFi CH 1 WiFi CH 2 Press and hold the specific WiFi Channel button for 6 seconds to change the connection to the specific WiFi Channel* *Note: If you change the WiFi channel while the wireless connection between the transmitter unit and receiver unit is established, both transmitter and receiver's WiFi channel will be changed simultaneously. If you change the WiFi channel while the wireless connection between the transmitter unit and receiver unit is not established, you would need to change and match up the same WiFi channel of the transmitter unit and receiver unit individually. 13 Selecting Specific Ports Front Panel Pushbutton You can cycle through the ports by pressing the front panel pushbutton Note: For the front panel pushbutton, both video and audio will switch port simultaneously. Remote Control You can press the specific port's button from the remote control Note 1: Video and audio will always switch simultaneously when switching receiver unit's output port. Note 2: If you have switched to a specific video port via remote control without specifying the audio port on the transmitter unit, by default, it will also switch the audio to that specific port. Note 3: Independent audio switching is only allowed for AV Audio and PC Audio. Note 4: You can select the transmitter unit's port by aiming the remote at the receiver unit or vice versa if and only if the connection between the transmitter unit and receiver unit has been established. If the connection has not yet been established, you would need to change the transmitter unit's port by aiming at the transmitter unit and change the receiver unit's port by aiming at the receiver unit. LED Indication Unit Transmitter unit/ Receiver unit LED Power/Link Description · Flash rapidly ­ performing a Wireless/LAN connection switch or firmware upgrade · Flash ­ the unit is booting up or establishing the connection between the transmitter unit and receiver unit · ON ­ the connection between transmitter unit and receiver unit has been successfully established It will be on if the specific port is selected; however, if the media source is turned off, not connected or the signal from the media source is not properly delivered, the LED will be flashing instead Transmitter unit HDMI1 HDMI2 PC AV Receiver unit HDMI Compo AV It will be on if the specific port is selected 14 IR Blast This allows you to control your media source by aiming your official remote that comes with your media source at the receiver unit. [. . . ] GREEN IOGEAR is an environmentally conscious company that emphasizes the importance of conserving natural resources. The use of our technology solutions helps reduce electronic waste. PART NO. [. . . ]