User manual IOGEAR GHDMIMS52 QUICK START GUIDE

[. . . ] Using this button, you can force the Wireless USB Hub to connect to one of three pre-associated PCs of your choosing. 1 2 3 Side View: WIRED WIRELESS AUTO MANUAL HUB ASSOC. ASSOC S1 Wired S2 4 5 Wireless Auto Manual (recommended) (recommended) 9 Installation Before we get started, please NOTE: Do not place Wireless USB devices under direct sunlight or near high heat emitting devices; Do not place Wireless USB devices near water or wet surfaces to avoid electric hazards; Do not place Wireless USB devices on any moving or unstable surfaces; 10 Hardware Preparation 1. Do not connect the Wireless USB Host Adapter to your computer until you are instructed to do so later in the section titled "Driver Installation. " 2. Remove the Wireless USB Host Adapter, Wireless USB Hub, USB 2. 0 A to Mini B Cable, power adapter, antenna, extension/swivel adapter, and the installation CD from the package. [. . . ] The first window will explain that WiCenter software is going to be installed on your computer, this software will control the devices so select - Next. 1c. Once . NET Framework 2. 0 is installed, the UWB software will automatically begin the installation process. The following window will request that you agree to the License Agreement before proceeding with installation, select Yes. 4. The window shown below allows you to select where the files for WiCenter are installed and stored. The following window confirms that you are approving installation, select - Next. 6. Once you have selected Next the WiCenter software will begin installation and show the status in a window similar to the one shown below. 16 7. Once all the software has been installed properly, you will see a window similar to the following stating installation has completed. After the software has fully installed, restart the PC. 8. 17 Driver Installation Verify that WiCenter is running by double-clicking on the WiCenter icon created on the desktop during the installation process. The first time that WiCenter is launched, the Wireless USB Connection Wizard will appear and will guide you through the Wireless USB connection process. Verify that the Wireless USB Host Adapter is connected to the extension/swivel adapter provided in the box. Plug the Wireless USB Host Adapter into an available USB port making sure that the extension/swivel adapter is adjusted to a 45 degree angle which will maximize range. If using a Desktop PC, do not plug the Wireless USB Host Adapter in the back of the PC. Re-insert the Wireless USB Host Adapter and reconnect power to the Wireless USB Hub. 2. Solution: Remove the Wireless USB Host Adapter from the PC and disconnect the power supply from the Wireless USB Hub. Re-insert Wireless USB Host Adapter, connect the power supply to the Wireless USB Hub and wait for the wireless connection. If still blinking, check the History window on WiCenter which will indicate if the IOGEAR Wireless USB Hub was associated. If not, associate the Wireless USB Host Adapter with the Wireless USB Hub using the mini-USB cable provided. Problem: Poor/Diminished range with the Wireless USB Host Adapter and Wireless USB Hub. Solution: Verify that the Wireless USB Host Adapter is utilizing the Extension/swivel adapter at a 45 degree angle. Verify that the Wireless USB Hub antenna is properly secured and is positioned vertically. If using a Desktop PC, do not plug the Wireless USB Host Adapter in the back of the PC. Plug the Wireless USB Host Adapter in the front of the system to ensure a good line-of-site signal with the Wireless USB Hub. Solution: Verify that the USB device has the ability to operate when connected to a hub of any kind by checking with the product documentation. [. . . ] This device is authorized under 47 CFR 15. 519 (the FCC Rules and Regulations). The operation of this device is subject to the following restriction: This UWB device shall transmit only when it is sending information to an associated receiver. This UWB device shall cease transmission within 10 seconds unless it receives an acknowledgement from the associated receiver that its transmission is being received. An acknowledgement of reception must continue to be received by the transmitting device at least every 10 seconds of operation or the UWB device must cease transmitting. 35 Contact IOGEAR, INC. [. . . ]