User manual INTEL DESKTOP BOARD DZ68ZV

[. . . ] Intel Desktop Board DZ68ZV Product Guide Order Number: G42421-001 Revision History Revision -001 Revision History First release of the Intel Desktop Board DZ68ZV Product Guide Date September 2011 Disclaimer INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH INTEL PRODUCTS. NO LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. EXCEPT AS PROVIDED IN INTEL?S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, INTEL ASSUMES NO LIABILITY WHATSOEVER, AND INTEL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY, RELATING TO SALE AND/OR USE OF INTEL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. Intel products are not intended for use in medical, life saving, or life sustaining applications. [. . . ] Table 9 shows the pin assignments for the alternate front panel header. Alternate Front Panel Power LED Header Signal Names Pin 1 2 3 Signal Name Front panel green LED No pin Front panel yellow LED Out In/Out Out Consumer IR (CIR) Headers The Desktop Board has two CIR headers: the input or receiver header (Figure 24, F) and the output or emitter header (Figure 24, E). The receiver header consists of a filtered translated infrared input compliant with Microsoft CIR specifications and a ?learning?The learning input is a high-pass input which the computer can use to ?learn?The emitter header consists of two output ports which the computer can use to emulate ?learned?infrared commands in order to control external electronic hardware. NOTE The Consumer IR option must be enabled in the system BIOS before it can function. Press <F2> at boot to enter the system BIOS, and go to Advanced > Peripheral Configuration > Enhanced Consumer IR, and set this option to Enabled. Table 10 shows the pin assignments and signal names for the front panel CIR receiver (input) header and Table 11 shows the pin assignments and signal names for the back panel CIR emitter (output) header. Front Panel CIR Receiver (Input) Header Signal Names Pin 1 3 5 7 Signal Name Ground No Connection +5 V Standby Key (no pin) Pin 2 4 6 8 Signal Name LED Learn-In Vcc CIR Input 51 Intel Desktop Board DZ68ZV Product Guide Table 11. Back Panel CIR Header Emitter (Output) Header Signal Names Pin 1 3 5 Signal Name Emitter Out 1 Ground Jack Detect 1 Pin 2 4 6 Signal Name Emitter Out 2 Key (no pin) Jack Detect 2 USB 2. 0 Headers Figure 24, G shows the location of the USB 2. 0 headers. Table 12 shows the pin assignments and signal names for each USB 2. 0 header. USB 2. 0 Header Signal Names USB Port A Pin 1 3 5 7 9 Signal Name Power (+5 V) DD+ Ground Key Pin 2 4 6 8 10 USB Port B Signal Name Power (+5 V) DD+ Ground No Connection NOTE Computer systems that have an unshielded cable attached to a USB port might not meet FCC Class B requirements, even if no device or a low-speed USB device is attached to the cable. Use a shielded cable that meets the requirements for a full-speed USB device. 52 Installing and Replacing Desktop Board Components Front Panel Header Figure 24, H shows the location of the front panel header. Table 13 shows the pin assignments and signal names for the front panel header. Front Panel Header Signal Names Pin 1 3 5 7 9 Description Hard Drive Activity LED Hard disk LED pull-up to +5 V Out Hard disk active LED Reset Switch Ground Reset switch Power Power Out 10 No pin In 6 8 Ground Not Connected Out 2 4 In/Out Pin Description Power LED Front panel green LED Front panel yellow LED On/Off Switch Power switch In Out Out In/Out NOTE When connecting individual wires from your chassis front panel to the front panel header, be sure to observe the connection polarity. Positive wires are usually solid color and negative wires are usually white or striped. Chassis Intrusion Header Figure 24, I shows the location of the chassis intrusion header. This header can be connected to a mechanical switch on the chassis to detect if the chassis cover is removed. This switch should be in the open position when the chassis cover is installed and closed when the cover is removed. Table 14 shows the pin assignments and signal names for the chassis intrusion header. Chassis Intrusion Header Signal Names Pin 1 2 Description Intruder# Ground 53 Intel Desktop Board DZ68ZV Product Guide Connecting to the Audio System After installing the Realtek audio driver from the Intel Express Installer DVD-ROM, the multi-channel audio feature can be enabled. The default connector assignments are shown in the table. Item A B C D E F Description Rear surround speakers S/PDIF output (optical) Center/subwoofer Line in Front speakers Mic in Figure 25. Back Panel Audio Connectors NOTE The back panel line out connector is designed to power either headphones or amplified speakers only. [. . . ] Japan VCCI (Voluntary Control Council for Interference) mark. Korea Certification mark. Includes an adjacent KCC (Korean Communications Commission) certification number: KCC-REM-CPU-DZ68ZV. Consists of a unique UL recognized manufacturer?s logo, along with a flammability rating (solder side). China RoHS/Environmentally Friendly Use Period Logo: This is an example of the symbol used on Intel Desktop Boards and associated collateral. [. . . ]