User manual INTEL DESKTOP BOARD DX58SO

[. . . ] Intel Desktop Board DX58SO Product Guide Order Number: E43167-002 Revision History Revision -001 -002 Revision History First release of the Intel Desktop Board DX58SO Product Guide Second release of the Intel Desktop Board DX58SO Product Guide Date August 2008 May 2010 If an FCC declaration of conformity marking is present on the board, the following statement applies: FCC Declaration of Conformity This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. For questions related to the EMC performance of this product, contact: Intel Corporation, 5200 N. E. Elam Young Parkway, Hillsboro, OR 97124 1-800-628-8686 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. [. . . ] Table 5 shows the pin assignments and signal names for the HD Audio Link header. HD Audio Link Header Signal Names Pin 1 3 5 7 9 11 13 15 Signal Name BCLK RST# SYNC SDO SDI0 SDI1 No Connection No Connection Pin 2 4 6 8 10 12 14 16 Signal Name Ground 3. 3 Vcc Ground 3. 3 Vcc +12 V Key 3. 3 V STBY Ground 47 Intel Desktop Board DX58SO Product Guide Consumer IR (CIR) Headers The Desktop Board has two CIR headers: the input or receiver header (Figure 27, D) and the output or emitter header (Figure 27, C). The receiver header consists of a filtered translated infrared input compliant with Microsoft CIR specifications and a ?learning?The learning input is a high-pass input which the computer can use to ?learn?The emitter header consists of two output ports which the computer can use to emulate ?learned?infrared commands in order to control external electronic hardware. NOTE The Consumer IR option must be enabled in the system BIOS before it can function. Press <F2> at boot to enter the system BIOS, and go to Advanced > Peripheral Configuration > Enhanced Consumer IR, and set this option to Enabled. Table 6 shows the pin assignments and signal names for the front panel CIR receiver (input) header and Table 7 shows the pin assignments and signal names for the back panel CIR emitter (output) header. Front Panel CIR Receiver (Input) Header Signal Names Pin 1 3 5 7 Signal Name Ground No Connection +5 V Standby Key (no pin) Pin 2 4 6 8 Signal Name LED Learn-In Vcc CIR Input Table 7. Back Panel CIR Header Emitter (Output) Header Signal Names Pin 1 3 5 Signal Name Emitter Out 1 Ground Jack Detect 1 Pin 2 4 6 Signal Name Emitter Out 2 Key (no pin) Jack Detect 2 48 Installing and Replacing Desktop Board Components Chassis Intrusion Header Figure 27, E shows the location of the chassis intrusion header. This header can be connected to a mechanical switch on the chassis to detect if the chassis cover is removed. Table 8 shows the pin assignments and signal names for the chassis intrusion header. Chassis Intrusion Header Signal Names Pin 1 2 Description Intruder Ground IEEE 1394a Header Figure 27, F shows the location of the IEEE 1394a header. Table 9 shows the pin assignments and signal names for the IEEE 1394a header. IEEE 1394a Header Signal Names Pin 1 3 5 7 9 Signal Name TPA1+ Ground TPA2+ +12 V Key (no pin) Pin 2 4 6 8 10 Signal Name TPA1Ground TPA2+12 V Ground 49 Intel Desktop Board DX58SO Product Guide USB 2. 0 Headers Figure 27, G shows the location of the USB 2. 0 headers. Table 10 shows the pin assignments and signal names for each USB 2. 0 header. USB 2. 0 Header Signal Names USB Port A Pin 1 3 5 7 9 Signal Name Power (+5 V) DD+ Ground Key Pin 2 4 6 8 10 USB Port B Signal Name Power (+5 V) DD+ Ground No Connection Note: USB ports may be assigned as needed. NOTE Computer systems that have an unshielded cable attached to a USB port might not meet FCC Class B requirements, even if no device or a low-speed USB device is attached to the cable. Use a shielded cable that meets the requirements for a full-speed USB device. Front Panel Header Figure 27, I shows the location of the front panel header. Table 11 shows the pin assignments and signal names for the front panel header. Front Panel Header Signal Names Pin 1 3 5 7 9 Description Hard Drive Activity LED Hard disk LED pull-up to +5 V Out Hard disk active LED Reset Switch Ground Reset switch Power Power Out 10 No pin In 6 8 Ground Not Connected Out 2 4 In/Out Pin Description Power LED Front panel green LED Front panel yellow LED On/Off Switch Power switch In Out Out In/Out 50 Installing and Replacing Desktop Board Components Alternate Front Panel Power LED Header Figure 27, H shows the location of the alternate front panel power LED header. Pins 1 and 3 of this header duplicate the signals on pins 2 and 4 of the front panel header. If your chassis has a three-pin power LED cable, connect it to this header. [. . . ] The SDT for Intel Desktop Board DX58SO is shown in Figure 33. Figure 33. Intel Desktop Board DX58SO China RoHS Material Self Declaration Table 81 Intel Desktop Board DX58SO Product Guide EMC Regulations Intel Desktop Board DX58SO complies with the EMC regulations stated in Table 20 when correctly installed in a compatible host system. EMC Regulations Regulation (Class B) FCC 47 CFR Part 15, Subpart B ICES-003 Issue 4 EN55022:2006 Title Title 47 of the Code of Federal Regulations, Part 15, Subpart B, Radio Frequency Devices. (Canada) Limits and methods of measurement of Radio Interference Characteristics of Information Technology Equipment. [. . . ]