User manual INTEL DESKTOP BOARD DH55PJ

[. . . ] Intel Desktop Board DH55PJ Product Guide Order Number: E93622-001 Revision History Revision -001 Revision History First release of the Intel Desktop Board DH55PJ Product Guide Date April 2010 Disclaimer INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH INTEL PRODUCTS. NO LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. EXCEPT AS PROVIDED IN INTEL?S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, INTEL ASSUMES NO LIABILITY WHATSOEVER, AND INTEL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY, RELATING TO SALE AND/OR USE OF INTEL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. Intel products are not intended for use in medical, life saving, or life sustaining applications. [. . . ] Push the card ejector lever down using the tip of a pencil or similar tool (Figure 18, B) in the notch. Pull the card straight up to remove it. 39 Intel Desktop Board DH55PJ Product Guide Figure 18. Removing a PCI Express x16 Graphics Card 40 Installing and Replacing Desktop Board Components Connecting Serial ATA (SATA) Cables SATA cables support the Serial ATA protocol. Each cable can be used to connect one internal SATA drive to the Desktop Board. Attach one end of the SATA cable to one of the SATA connectors on the board (Figure 19, A) and attach the other end of the cable to the SATA drive (Figure 19, B). Figure 19. Connecting a Serial ATA Cable 41 Intel Desktop Board DH55PJ Product Guide Connecting to the Internal Headers Before connecting cables to any of the internal headers, observe the precautions in ?Before You Begin?Figure 20 shows the location of the internal headers and connectors on Intel Desktop Board DH55PJ. Figure 20. Internal Headers 42 Installing and Replacing Desktop Board Components Front Panel Audio Header The front panel audio header shown in Figure 20, A supports both Intel High Definition (HD) Audio and AC ?97 Audio. Table 4 shows the pin assignments and signal names for HD Audio and Table 5 shows the pin assignments and signal names for AC ?97 Audio. Front Panel Audio Signal Names for Intel HD Audio Pin 1 3 5 7 9 Signal Name PORT 1L (Microphone) PORT 1R (Microphone) PORT 2R (Headphone) SENSE_SEND PORT 2L (Headphone) Pin 2 4 6 8 10 Signal Name GND PRESENCE# SENSE1_RETURN KEY (no pin) SENSE2_RETURN Table 5. Front Panel Audio Header Signal Names for AC ?97 Audio Pin 1 3 5 7 9 Signal Name MIC MIC_BIAS FP_OUT_R AUD_5V FP_OUT_L Pin 2 4 6 8 10 Signal Name AUD_GND AUD_GND FP_RETURN_R KEY (no pin) FP_RETURN_L Internal Mono Speaker Header The internal mono speaker header is shown in Figure 20, B. Table 6 shows the pin assignments and signal names for the internal mono speaker header. + 43 Intel Desktop Board DH55PJ Product Guide S/PDIF Header Figure 20, C shows the location of the S/PDIF output header. Table 7 shows the pin assignments and signal names for the S/PDIF output header. S/PDIF Header Signal Names Pin 1 2 3 4 Description Ground S/PDIF Out Key (no pin) +5 VDC Parallel Port Header Figure 20, D shows the location of the parallel port header. Table 8 shows the pin assignments and signal names for the parallel port header. Parallel Port Header Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 Standard Signal Name STROBE# AUTOFD# PD0 FAULT# PD1 INT# PD2 SLCTIN# PD3 GROUND PD4 GROUND PD5 GROUND PD6 GROUND PD7 GROUND ACK# GROUND BUSY GROUND ECP Signal Name STROBE# AUTOFD#, HOSACK PD0 FAULT#, PERIPHREQST# PD1 INT#, REVERSERQST# PD2 SLCTIN# PD3 GROUND PD4 GROUND PD5 GROUND PD6 GROUND PD7 GROUND ACK# GROUND BUSY#, PERIPHACK GROUND EPP Signal Name WRITE# DATASTB# PD0 FAULT# PD1 RESET# PD2 ADDRSTB# PD3 GROUND PD4 GROUND PD5 GROUND PD6 GROUND PD7 GROUND INTR GROUND WAIT# GROUND 44 Installing and Replacing Desktop Board Components Pin 23 24 25 26 Standard Signal Name PERROR GROUND SELECT KEY (no pin) ECP Signal Name PE, ACKREVERSE# GROUND SELECT KEY (no pin) EPP Signal Name PE GROUND SELECT KEY (no pin) Alternate Front Panel Power LED Header Figure 20, E shows the location of the alternate front panel power LED header. Pins 1 and 3 of this header duplicate the signals on pins 2 and 4 of the front panel header. If your chassis has a three-pin power LED cable, connect it to this header. Table 9 shows the pin assignments for the alternate front panel header. Alternate Front Panel Power LED Header Signal Names Pin 1 2 3 Signal Name Front panel LED+ No pin Front panel LEDOut In/Out Out Front Panel Header Figure 20, F shows the location of the front panel header. Table 10 shows the pin assignments and signal names for the front panel header. [. . . ] If this is used near a radio or television receiver in a domestic environment, it may cause radio interference. Install and use the equipment according to the instruction manual. 72 Regulatory Compliance Korea Class B Statement Korea Class B Statement translation: This equipment is for home use, and has acquired electromagnetic conformity registration, so it can be used not only in residential areas, but also other areas. Ensure Electromagnetic Compatibility (EMC) Compliance Before computer integration, make sure that the power supply and other modules or peripherals, as applicable, have passed Class B EMC testing and are marked accordingly. Pay close attention to the following when reading the installation instructions for the host chassis, power supply, and other modules: ?Product certifications or lack of certifications External I/O cable shielding and filtering Mounting, grounding, and bonding requirements Keying connectors when mating the wrong connectors could be hazardous If the power supply and other modules or peripherals, as applicable, are not Class B EMC compliant before integration, then EMC testing may be required on a representative sample of the newly completed computer. 73 Intel Desktop Board DH55PJ Product Guide Product Certifications Board-Level Certifications Intel Desktop Board DH55PJ has the regulatory compliance marks shown in Table 19. [. . . ]