User manual INTEL DESKTOP BOARD DG43RK

[. . . ] Intel Desktop Board DG43RK Product Guide Order Number: E88305-001 Revision History Revision -001 Revision History First release of the Intel Desktop Board DG43RK Product Guide Date February 2010 Disclaimer INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH INTEL PRODUCTS. NO LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. EXCEPT AS PROVIDED IN INTEL?S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, INTEL ASSUMES NO LIABILITY WHATSOEVER, AND INTEL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY, RELATING TO SALE AND/OR USE OF INTEL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. Intel products are not intended for use in medical, life saving, or life sustaining applications. [. . . ] Depending on the over-current protection of the power supply, certain Desktop Board components and/or traces may be damaged. Installing a PCI Express x16 Card 1. Place the card in the PCI Express x16 connector (Figure 18, A) and press down on the card until it is completely seated in the connector and the card retention notch on the card snaps into place around the retention mechanism pin on the connector. Secure the card?s metal bracket to the chassis back panel with a screw (Figure 18, B). Figure 18. Installing a PCI Express x16 Card 43 Intel Desktop Board DG43RK Product Guide Removing the PCI Express x16 Card Follow these instructions to remove the PCI Express x16 card from the connector: 1. Remove the screw (Figure 19, A) that secures the card?s metal bracket to the chassis back panel. Push the card ejector lever down using the tip of a pencil or similar tool (Figure 19, B) in the notch. Removing a PCI Express x16 Card 44 Installing and Replacing Desktop Board Components Connecting a PATA (IDE) Cable An IDE cable can be used to connect two IDE drives to the Desktop Board. Figure 20 shows the correct installation of the cable. NOTES ATA-66/100 compatible cables are backward compatible with drives using slower IDE transfer protocols. If an ATA-66/100 disk drive and a disk drive using any other IDE transfer protocol are attached to the same cable, the maximum transfer rate between the drives may be reduced to that of the slowest drive. Do not connect an ATA device as a slave on the same IDE cable as an ATAPI master device. For example, do not connect an ATA hard drive as a slave to an ATAPI CD-ROM drive. Attach the cable end with the single connector (blue) to the Intel Desktop Board (Figure 20, A). Attach the cable end with the two closely spaced connectors (gray and black) to the drives (Figure 20, B). Figure 20. Connecting the IDE Cable 45 Intel Desktop Board DG43RK Product Guide Connecting Serial ATA (SATA) Cables SATA cables support the Serial ATA (SATA) protocol. Each cable can be used to connect a single SATA drive to the Desktop Board. Attach one end the SATA cable to one of the SATA connectors on the board (Figure 21, A). Attach the other end of the SATA cable to the SATA drive (Figure 21, B). Figure 21. Connecting a Serial ATA Cable 46 Installing and Replacing Desktop Board Components Connecting to Internal Headers Before connecting cables to the internal headers, observe the precautions in ?Before You Begin?Internal Headers 47 Intel Desktop Board DG43RK Product Guide S/PDIF Header Figure 22, A shows the location of the S/PDIF header. Table 5 shows the pin assignments and signal names for the S/PDIF header. S/PDIF Connector Signal Names Pin 1 2 3 4 Signal Name Ground S/PDIF Out Key (no pin) +5 VDC Front Panel HD Audio Header The front panel audio header shown in Figure 22, B supports both Intel HD Audio and AC ?97 Audio. Table 6 shows the pin assignments and signal names for HD Audio and Table 7 shows the pin assignments and signal names for AC ?97 Audio. [. . . ] If this is used near a radio or television receiver in a domestic environment, it may cause radio interference. Install and use the equipment according to the instruction manual. 76 Regulatory Compliance Korea Class B Statement Korea Class B Statement translation: This equipment is for home use, and has acquired electromagnetic conformity registration, so it can be used not only in residential areas, but also other areas. Ensure Electromagnetic Compatibility (EMC) Compliance Before computer integration, make sure that the power supply and other modules or peripherals, as applicable, have passed Class B EMC testing and are marked accordingly. Pay close attention to the following when reading the installation instructions for the host chassis, power supply, and other modules: ?Product certifications or lack of certifications External I/O cable shielding and filtering Mounting, grounding, and bonding requirements Keying connectors when mating the wrong connectors could be hazardous If the power supply and other modules or peripherals, as applicable, are not Class B EMC compliant before integration, then EMC testing may be required on a representative sample of the newly completed computer. 77 Intel Desktop Board DG43RK Product Guide Product Certifications Board-Level Certification Markings Intel Desktop Board DG43RK has the product certification markings shown in Table 21. [. . . ]