User manual INTEL DESKTOP BOARD DB43LD

[. . . ] Intel Desktop Board DB43LD Product Guide Order Number: E65075-001 Revision History Revision -001 Revision History First release of the Intel Desktop Board DB43LD Product Guide Date March 2009 If an FCC declaration of conformity marking is present on the board, the following statement applies: FCC Declaration of Conformity This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. For questions related to the EMC performance of this product, contact: Intel Corporation, 5200 N. E. Elam Young Parkway, Hillsboro, OR 97124 1-800-628-8686 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. [. . . ] If the card is not fully seated in the PCI Express connector, an electrical short may result across the PCI Express connector pins. Depending on the over-current protection of the power supply, certain Desktop Board components and/or traces may be damaged. Installing a PCI Express x16 Card CAUTION When installing a PCI Express x16 card on the desktop board, ensure that the card is fully seated in the PCI Express x16 connector before you power on the system. If the card is not fully seated in the PCI Express connector, an electrical short may result across the PCI Express connector pins. Depending on the over-current protection of the power supply, certain desktop board components and/or traces may be damaged. Place the card in the PCI Express x16 connector (Figure 17, A) and press down on the card until it is completely seated in the connector and the card retention notch snaps into place around the retention mechanism pin. Secure the card?s metal bracket to the chassis back panel with a screw (Figure 17, B). 41 Intel Desktop Board DB43LD Product Guide Figure 17. Installing a PCI Express x16 Card 42 Installing and Replacing Desktop Board Components Removing the PCI Express x16 Card Follow these instructions to remove the PCI Express x16 card from the connector: 1. Remove the screw (Figure 18, A) that secures the card?s metal bracket to the chassis back panel. Push the card ejector lever down using the tip of a pencil or similar tool in the notch (Figure 18, B). Removing a PCI Express x16 Card 43 Intel Desktop Board DB43LD Product Guide Connecting SATA Devices SATA cables support the Serial ATA protocol. Each cable can be used to connect a single SATA drive to the Desktop Board. Attach one end the SATA cable to one of the black SATA connectors on the board (Figure 19, A). Attach the other end of the SATA cable to the SATA drive (Figure 19, B). Figure 19. Connecting a Serial ATA Cable To connect an eSATA drive you must use an adapter that cables from the red eSATA connector (Figure 1, R) to a back panel connector. 44 Installing and Replacing Desktop Board Components Connecting to Internal Headers Before connecting cables to the internal headers, observe the precautions in ?Before You Begin?Figure 20 shows the location of the internal headers and connectors. Figure 20. Internal Headers 45 Intel Desktop Board DB43LD Product Guide S/PDIF Header See Figure 20, A for the location of the S/PDIF header. Table 6 shows the pin assignments and signal names for the S/PDIF header. S/PDIF Header Pin 1 2 3 Signal Name Ground S/PDIF out VCC (5V) Front Panel Audio Header The front panel audio header (Figure 20, B) supports both Intel HD Audio and AC ?97 audio. Table 7 shows the pin assignments and signal names for HD Audio and Table 8 shows the pin assignments and signal names for AC ?97 Audio. Front Panel Audio Header Signal Names for Intel HD Audio Pin 1 3 5 7 9 Signal Name PORT 1L PORT 1R PORT 2R SENSE_SEND PORT 2L Pin 2 4 6 8 10 Signal Name GND PRESENCE# SENSE1_RETURN KEY (no pin) SENSE2_RETURN Table 8. Front Panel Audio Header Signal Names for AC ?97 Audio Pin 1 3 5 7 9 Signal Name MIC MIC_BIAS FP_OUT_R AUD_5V FP_OUT_L Pin 2 4 6 8 10 Signal Name AUD_GND AUD_GND FP_RETURN_R KEY (no pin) FP_RETURN_L 46 Installing and Replacing Desktop Board Components Serial Port Header See Figure 20, C for the location of the serial port header. Serial Port Header Signal Names Pin 1 3 5 7 9 Signal Name DCD TXD# Ground RTS RI Pin 2 4 6 8 10 Signal Name RXD# DTR DSR CTS No Connection Alternate Front Panel Power LED Header Figure 20, D shows the location of the alternate front panel power LED header. [. . . ] Intel Desktop Board DB43LD China RoHS Material Self Declaration Table 75 Intel Desktop Board DB43LD Product Guide EMC Regulations Intel Desktop Board DB43LD complies with the EMC regulations stated in Table 20 when correctly installed in a compatible host system. EMC Regulations Regulation (Class B) FCC 47 CFR Part 15, Subpart B ICES-003 Issue 4 EN55022:2006 Title Title 47 of the Code of Federal Regulations, Part 15, Subpart B, Radio Frequency Devices. (Canada) Limits and methods of measurement of Radio Interference Characteristics of Information Technology Equipment. (European Union) Australian Communications Authority, Standard for Electromagnetic Compatibility. [. . . ]