User manual INTEL D915GEV

[. . . ] Intel Desktop Board D915GEV/D915GUX/ D915GAV/D915GAG Product Guide Order Number: C64136-002 Revision History Revision -001 -002 Revision History First release of the Desktop Board D915GEV/D915GUX/ D915GAV/D915GAG Product Guide. Second release of Intel Desktop Board D915GEV/D915GUX/ D915GAV/D915GAG Product Guide. Intel Date June 2004 September 2004 If an FCC declaration of conformity marking is present on the board, the following statement applies: FCC Declaration of Conformity This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. [. . . ] Always replace the processor back to the package if the processor is removed from the socket (see Figure 10). Figure 10. Remove the Processor from the Protective Processor Cover/Do Not Touch 33 Intel Desktop Board D915GEV/D915GUX/D915GAV/D915GAG Product Guide 6. Hold the processor with your thumb and index fingers oriented as shown in Figure 11. Lower the processor straight down without tilting or sliding the processor in the socket. G G HF H F Figure 11. Pressing down on the load plate (Figure 12, I) close and engage the socket lever (Figure 12, J). J Figure 12. Close the Load Plate Installing the Processor Fan Heat Sink Desktop Board D915GEV/D915GUX/D915GAV/D915GAG has an integrated processor fan heat sink retention mechanism (RM). For instructions on how to attach the processor fan heat sink to the integrated processor fan heat sink RM, refer to the boxed processor manual or the Intel World Wide Web site at: http://support. intel. com/support/processors/pentium4/intnotes478. htm 34 II I Installing and Replacing Desktop Board Components Connecting the Processor Fan Heat Sink Cable Connect the processor fan heat sink cable to the 4-pin processor fan connector (see Figure 13). OM16894 Figure 13. Connecting the Processor Fan Heat Sink Cable to the Processor Fan Connector Removing the Processor For instruction on how to remove the processor fan heat sink and processor, refer to the processor installation manual or the Intel World Wide Web site at: http://support. intel. com/support/processors/pentium4/intnotes478. htm 35 Intel Desktop Board D915GEV/D915GUX/D915GAV/D915GAG Product Guide Installing and Removing Memory NOTE To be fully compliant with all applicable Intel SDRAM memory specifications, the boards require DIMMs that support the Serial Presence Detect (SPD) data structure. You can access the PC Serial Presence Detect Specification at: http://www. intel. com/technology/memory/pcsdram/spec/ Desktop boards D915GAV and D915GAG have four 184-pin DDR DIMM sockets arranged as DIMM 0 (blue) and DIMM 1 (black) in both Channel A and Channel B. Desktop boards D915GEV and D915GUX have four 240-pin DDR2 DIMM sockets arranged as DIMM 0 (blue) and DIMM 1 (black) in both Channel A and Channel B. Guidelines for Dual Channel Memory Configuration Before installing DIMMs, read and follow these guidelines for dual channel configuration. Two or Four DIMMs Install a matched pair of DIMMs equal in speed and size in DIMM 0 (blue) of both channels A and B (see Figure 14). Channel A 1 GB, 400 MHz Channel B 1 GB, 400 MHz DIMM 0 DIMM 1 DIMM 0 DIMM 1 Figure 14. Dual Configuration Example 1 36 Installing and Replacing Desktop Board Components If additional memory is to be used, install another matched pair of DIMMs in DIMM 1 (black) in both channels A and B (see Figure 15). Channel A 256 MB, 400 MHz 512 MB, 400 MHz Channel B 256 MB, 400 MHz 512 MB, 400 MHz DIMM 0 DIMM 1 DIMM 0 DIMM 1 Figure 15. Dual Configuration Example 2 Three DIMMs Install a matched pair of DIMMs equal in speed and size in DIMM 0 (blue) and DIMM 1 (black) of channel A. Install a DIMM equal in speed and total size of the DIMMs installed in channel A in either DIMM 0 or DIMM 1 of channel B (see Figure 16). Channel A 256 MB, 400 MHz 256 MB, 400 MHz Channel B 512 MB, 400 MHz DIMM 0 DIMM 1 DIMM 0 DIMM 1 Figure 16. Dual Configuration Example 3 NOTE All other memory configurations will result in single channel memory operation. 37 Intel Desktop Board D915GEV/D915GUX/D915GAV/D915GAG Product Guide Installing DIMMs CAUTION Install memory in the DIMM sockets prior to installing the PCI Express video card to avoid interference with the memory retention mechanism. To make sure you have the correct DIMM, place the DIMM on the illustration in Figure 17. DDR DDR2 mm 1 2 3 4 5 6 7 8 9 10 11 12 13 OM16847 Figure 17. Matching the Correct DIMM 38 Installing and Replacing Desktop Board Components 1. Remove the computer's cover and locate the DIMM sockets (see Figure 18). Channel A DIMM 0 DIMM 1 Channel B DIMM 0 DIMM 1 OM16895 Figure 18. Remove the PCI Express video card if it interferes with the DIMM retaining clips from being easily opened and closed. Make sure the clips at either end of the DIMM socket(s) are pushed outward to the open position. Holding the DIMM by the edges, remove it from its anti-static package. Align the small notch at the bottom edge of the DIMM with the keys in the socket (see inset in Figure 18). When the DIMM is inserted, push down on the top edge of the DIMM until the retaining clips snap into place. [. . . ] Franais Ce produit est conforme aux exigences de la Directive Europenne 89/336/EEC & 73/23/EEC. Deutsch Dieses Produkt entspricht den Bestimmungen der Europischen Richtlinie 89/336/EEC & 73/23/EEC. Icelandic essi vara stenst regluger Evrpska Efnahags Bandalagsins nmer 89/336/ EEC & 73/23/EEC. Italiano Questo prodotto conforme alla Direttiva Europea 89/336/EEC & 73/23/EEC. [. . . ]