User manual INDESIT HI591IX

[. . . ] 10 Worktop illumination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 3 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ INSTALLATION This canopy hood is designed to be fixed to any rigid vertical surface, over a gas or electric hotplate and can be used either in the extraction mode (ducted to the outside) or in the recirculation mode (internal recycling). ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ Safety warnings • Before commencing the installation, consideration should be given to the difficulties to be found during installation and to the bulky weight of the hood. The installation work must be undertaken by a qualified and competent person in conformity to the rules concerning the evacuation of contaminated air. [. . . ] • Never leave frying pans unattended during use as overheated fats and oils may catch fire. • If the room where the cooker hood is to be used contains a fuel burning appliance such as a central heating boiler then this must be of the room sealed or balanced flue type. If other types of flue or appliance are fitted ensure that there is an adequate supply of air into the room. When the cooker hood is used in conjunction with other appliances supplied with energy other than electric, the negative pressure in the room must not exceed 0, 04 mbar to prevent fumes being drawn back into the room by the cooker hood. Components • • The cooker hood is made up of the following components (fig 1): n. 2 wall brackets 2 to fix the chimney, rawl plugs, screws, and documentation n. 1 S I C • • • • • ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 4 GB ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ Instructions for Installation • • • • • For easy installation proceed as follows: Fix the wall brackets and Splashback. Connect the hood to the mains supply and ensure that it works properly. Fix the telescopic metal frame. Fixing the wall brackets (and splashback) Ref. 2a-b • Draw a vertical line on the wall, from the centre of the cooking appliance up to the ceiling, using a marking pen. Fixing the wall brackets 1: • Put the bracket I to the wall, aligning its marked centre across the vertical line, ensuring that the distance between the centres of the holes and the cooking area is as follows: • Draw a horizontal line on the wall ensuring that the distance from the cooktop is as follows: a) when the splasback is to be installed: d = 270 mm + H, where H is the height of the visible part of the splashback; as the splashback can be of different heights, the correct H figure can only be obtained by measuring the actual height of the splashback to be fitted. b) without splashback d = 875 mm minimum. 2 1 d = 875 min 115 140 2 1 265 650 min 115 140 243_A02 X X Fig. • If the hood is provided with the charcoal filters fitted, the filters should be removed (see paragraph Maintenance). Recirculation fitting • The filtered air is returned to the room through the two side grilles on U-shaped lower section I, which are either formed in the metal itself (fig. • Fit the recirculation spigot item R into the round outlet on top of the canopy while pressing down on the spigot until it snaps into position. • Install the charcoal filters inside the canopy as instructed in paragraph Maintenance). A Fig. 5 R 243_A05 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ GB 7 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ Electrical connection and working test • Before connecting to the mains supply ensure that the mains voltage corresponds with the voltage on the rating plate inside the hood. • Connect the cooker hood to the mains via a double pole switch which has 3 mm clearance between the contacts. • Once the electrical connection has been completed, check that worktop illumination, motor and speed work properly. Fitting the telescopic chimney stack • Fit the two plastic supports provided to the top part of the hood. • To fit the upper section item S first expand the chimney slightly to allow it to fit over the wall brackets (item 2 fig. • The lower section item I of the chimney stack should be fitted between the lower bracket 2 and the wall. • Fix the U-shaped section to the plastic supports, using two of the screws provided in the bag of accessories (fig. Special attention should be paid to the grease filters and to the charcoal filters when the hood is used in the recirculation mode. ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ Metal grease filters Cleaning The metal grease filter should be cleaned every two months with normal usage and can be cleaned in a dishwasher or by hand using a mild detergent or liquid soap. [. . . ] 8 Charcoal filters Functioning In the recycling mode the charcoal filters absorb smells and odours. This hood is designed to be fitted with two charcoal filters on both sides of the fan unit (fig. The charcoal filter cannot be washed and should be replaced at least every 4 months or more frequently if the hood is used consistently. Replacement • To remove the charcoal filters place on hand on one filter at a time and turn it toward the front part. [. . . ]