User manual HUSKY HU80522

[. . . ] OPERATOR'S MANUAL GASOLINE PRESSURE WASHER HU80522 Your pressure washer has been engineered and manufactured to our high standard for dependability, ease of operation, and operator safety. When properly cared for, it will give you years of rugged, trouble-free performance. WARNING: To reduce the risk of injury, the user must read and understand the operator's manual before using this product. Thank you for your purchase. SAVE THIS MANUAL FOR FUTURE REFERENCE TABLE OF CONTENTS Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] SPRAY WAND GROOVED GRIPPING SURFACE CONNECTING HIGH PRESSURE HOSE TO SPRAY WAND ASSEMBLY See Figure 6. Screw the collar on the high pressure hose into the spray wand's inlet coupler by turning the hose collar clockwise. Pull on the hose to be certain it is properly secured. CONNECTOR SPRAY WAND EXTENSION Fig. 6 11 ASSEMBLY CONNECTING THE HIGH PRESSURE HOSE TO THE PUMP See Figure 7. After the high pressure hose has been uncoiled and attached to the spray wand: Align the collar on the threaded nipple on the pump. Insert the nozzle on the end of the high pressure hose collar into the threaded nipple. THREADED NIPPLE COLLAR CONNECTING THE GARDEN HOSE TO THE PRESSURE WASHER See Figure 8. Before connecting the garden hose to the pressure washer: Run water through the hose for 30 seconds to clean any debris from the hose. If the screen is damaged, do not use the machine until the screen has been replaced. If the screen is dirty, clean it before connecting the garden hose to the machine. NOTE: There must be a minimum of 10 feet of unrestricted hose between the pressure washer intake and the hose faucet or shut off valve (such as a "Y" shut off connector). With the hose faucet turned completely off, attach the end of the garden hose to the water intake. 8 12 OPERATION WARNING: Do not allow familiarity with tools to make you careless. Remember that a careless fraction of a second is sufficient to inflict serious injury. WARNING: Always wear safety goggles or safety glasses with side shields when operating tools. Failure to do so could result in objects being thrown into your eyes, resulting in possible serious injury. PRIMER BULB 3X RECOIL STARTER WARNING: Do not use any attachments or accessories not recommended by the manufacturer of this tool. The use of attachments or accessories not recommended can result in serious personal injury. WARNING: Do not direct discharge stream at persons. Failure to heed this warning could result in serious injury. APPLICATIONS You may use this tool for the purposes listed below: Removing dirt and mold from decks, cement patios, and house siding Cleaning cars, boats, motorcycles, outdoor furniture, and grills Fig. 9 OFF SWITCH STARTING AND STOPPING THE PRESSURE WASHER See Figures 9 - 10. CAUTION: Do not run the pump without the water supply connected and turned on. Turn the garden hose on then squeeze the trigger to relieve air pressure; hold the trigger until a steady stream of water appears. NOTE: If starting the engine for the first time, push the primer bulb 5 times. 10 To stop the engine: Press and hold the switch in the OFF position for three (3) seconds or until the engine stops. OPERATION USING THE SPRAY WAND TRIGGER See Figure 11. [. . . ] to be defective in material or workmanship will be repaired or replaced, without charge for parts and labor, by an Authorized Service Center for HUSKY® brand pressure washers (Authorized HUSKY® Service Center). The product, including any defective part, must be returned to an Authorized HUSKY® Service Center within the warranty period. The expense of delivering the product to the service center for warranty work and the expense of returning it back to the owner after repair or replacement will be paid for by the owner. Techtronic Industries North America, Inc. 's responsibility in respect to claims is limited to making the required repairs or replacements and no claim of breach of warranty shall be cause for cancellation or rescission of the contract of sale of any HUSKY® brand pressure washer. [. . . ]