User manual HP VISUALIZE J5000 WORKSTATION

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual HP VISUALIZE J5000 WORKSTATION. We hope that this HP VISUALIZE J5000 WORKSTATION user guide will be useful to you.


HP VISUALIZE J5000 WORKSTATION : Download the complete user guide (4596 Ko)

You may also download the following manuals related to this product:

   HP visualize j5000 workstation annexe 1 (1944 ko)
   HP visualize j5000 workstation annexe 2 (1984 ko)
   HP visualize j5000 workstation annexe 3 (59 ko)
   HP visualize j5000 workstation annexe 4 (1984 ko)
   HP VISUALIZE J5000 WORKSTATION BROWSABLE CD BOOKLET (95 ko)
   HP VISUALIZE J5000 WORKSTATION IRIX TO -UX MIGRATION GUIDE (649 ko)
   HP VISUALIZE J5000 WORKSTATION OVERVIEW OF THE VISUALIZE FX GRAPHICS (335 ko)
   HP VISUALIZE J5000 WORKSTATION WORKSTATION J5000 AND J7000 - SITE PREPARATION (427 ko)
   HP VISUALIZE J5000 WORKSTATION PA-RISC VISUALIZE WORKSTATION UNIVERSAL SERIAL BUS (7396 ko)
   HP VISUALIZE J5000 WORKSTATION TROUBLESHOOTING GUIDE FOR SCR+DMI: 9000 COMPUTERS (80 ko)
   HP VISUALIZE J5000 WORKSTATION WORKSTATIONS - -UX 10.20 GRAPHICS ADMINISTRATION GUIDE (2603 ko)
   HP VISUALIZE J5000 WORKSTATION VISUALIZE B1000, C3000, J5000 WORKSTATION MEMORY SUBSYSTEM (122 ko)
   HP VISUALIZE J5000 WORKSTATION 6 DEGREES OF FREEDOM CAD INPUT DEVICES A43161C TECHNICAL DATA (193 ko)
   HP VISUALIZE J5000 WORKSTATION VISUALIZE B1000, C3000, J5000 WORKSTATIONS SOFTWARE SOLUTION (58 ko)
   HP VISUALIZE J5000 WORKSTATION VISUALIZE WORKSTATION - NT & -UX FUNCTIONAL INTEROPERABILITY (41 ko)
   HP VISUALIZE J5000 WORKSTATION WORKSTATION -UX - VISUALIZE FX GRAPHICS CARD INSTALLATION GUIDE (446 ko)
   HP VISUALIZE J5000 WORKSTATION VISUALIZE J5000, J7000 WORKSTATIONS SERVICE HANDBOOK (A4476-90039) (3914 ko)
   HP VISUALIZE J5000 WORKSTATION VISUALIZE J5000, J7000 WORKSTATIONS SERVICE HANDBOOK (A4978-90039) (3862 ko)
   HP VISUALIZE J5000 WORKSTATION VISUALIZE J5000, J7000 WORKSTATIONS SERVICE HANDBOOK (A4978-90048) (7715 ko)
   HP VISUALIZE J5000 WORKSTATION VISUALIZE J5000, J7000 WORKSTATIONS SERVICE HANDBOOK (A4978-90049) (4385 ko)
   HP VISUALIZE J5000 WORKSTATION WORKSTATIONS - GRAPHICS ADMINISTRATION GUIDE FOR RED HAT LINUX 6.2 (1128 ko)
   HP VISUALIZE J5000 WORKSTATION VISUALIZE J5000, J7000 WORKSTATIONS SITE PREPARATION GUIDE (A4978-90021) (427 ko)
   HP VISUALIZE J5000 WORKSTATION VISUALIZE WORKSTATION - FXE GRAPHICS CARD INSTALLATION GUIDE (A4552-90016) (132 ko)
   HP VISUALIZE J5000 WORKSTATION VISUALIZE WORKSTATION - MIGRATING UNIX TECHNICAL ENVIRONMENTS TO WINDOWS NT (54 ko)
   HP VISUALIZE J5000 WORKSTATION VISUALIZE J5000 TO J5600 WORKSTATION PA8600 UPGRADE INSTRUCTIONS (A5998-90000) (342 ko)
   HP VISUALIZE J5000 WORKSTATION ENTERPRISE FILE SYSTEM: PLANNING AND CONFIGURING DCE/9000 ENHANCED DFS VERSION (736 ko)
   HP VISUALIZE J5000 WORKSTATION ENTERPRISE FILE SYSTEM: RELEASE NOTE FOR DCE/9000 ENHANCED DFS VERSION 3.0 (B6 (173 ko)
   HP VISUALIZE J5000 WORKSTATION VISUALIZE FX GRAPHICS CARD FAMILY (INCLUDING FXE, FX5, AND FX10) INSTALLATION A (421 ko)
   HP VISUALIZE J5000 WORKSTATION VISUALIZE FX GRAPHICS CARD FAMILY (INCLUDING FXE, FX5, AND FX10) INSTALLATION A (446 ko)
   HP VISUALIZE J5000 WORKSTATION VISUALIZE J5000, J7000 WORKSTATIONS PARTS REMOVAL AND REPLACEMENT GUIDE (A4978- (1110 ko)

Manual abstract: user guide HP VISUALIZE J5000 WORKSTATION

Detailed instructions for use are in the User's Guide.

[. . . ] J Class Owner's Guide R Workstation Systems Group HP Part No. A4476­90013 Edition E0596 Printed in U. S. A. © Hewlett-Packard Co. 1995 First Printing: Latest Printing: January 1995 May 1996 UNIX is a registered trademark in the United States and other countries, licensed exclusively through X/Open Company Limited. NOTICE The information contained in this document is subject to change without notice. [. . . ] Removing EMI Plate 7. Disconnect the SCSI and power cables from the drive. B-12 8. Unscrew the two screws holding the drive in the storage drawer, and slide the drive out of the drawer. Removing Drive Screws 9. Check the SCSI address/jumper settings on the replacement drive, using the following information sections. B-13 CD-ROM Drive The CD-ROM drive ships with the drive set to SCSI ID address 2. We recommend keeping the address setting at 2 unless it is used by another device. CAUTION: CD-ROM drives are susceptible to mechanical and electrostatic shock. When handling the drive, always wear the static-grounding wrist strap that came in the CD-ROM drive kit. If you need to change the CD-ROM drive's address, follow these instructions, referring to Figure A­6. If you do not need to change the drive's address, go to Step 10 of this installation procedure. To change the address, use needlenose pliers to set the drive's SCSI ID to an address that is not used by another SCSI device. The host SCSI controller uses SCSI ID 7. NOTICE: 3. Use needlenose pliers to remove the SCSI terminators, if still attached to the drive. B-14 Rear View SCSI ID Address 0 1 2 3 4 5 6 7 Jumpers ID 1 ID 2 ID 4 TERM TEST PRV/ALM PRTY ID 4 ID 2 ID 1 Figure A­6. CD-ROM Drive SCSI Address/Jumper Settings B-15 DDS Tape Drive The DDS tape drive ships with the drive set to SCSI ID address 3 and the Operation Mode switches set for correct drive operation. We recommend keeping the address setting at 3 unless it is used by another device. CAUTION: SCSI tape drives are susceptible to mechanical and electrostatic shock. When handling the drive, always wear the static-grounding wrist strap that came in the DDS tape drive kit. If you need to change the DDS tape drive's address or operation mode, follow these instructions, referring to Figure A­7 for the DDS-DC drive, Figure A­8 for the DDS-2 drive, and Figure A­9 for operation mode. If you do not need to change the drive's address or operation mode, go to Step 10 of this installation procedure. To change the jumper settings, use needlenose pliers to set the drive's SCSI ID to an address that is not used by another SCSI device. 4. Use needlenose pliers to remove the SCSI terminators, if still attached to the drive. If you need to change the Operation Mode switches, locate the switches on the underside of the DDS tape drive. Switches 1 and 2 are used to configure the data compression operation mode. Switches 3 through 8 are used to specify drive connectivity and functionality according to host or customer requirements. Figure A­9 shows the available options. B-16 SCSI Terminators (must be removed) Target ID Term PWR ID2 Jumpers ID1 ID0 Target ID Term PWR ID2 Jumpers ID1 ID0 0 1 2 3 (Default) 4 5 6 Figure A­7. DDS-DC Tape Drive SCSI Address/Jumper Settings B-17 Bit 0 Bit1 Bit 2 Term PWR SCSI Connector SCSI ID Term PWR* Bit 2 SCSI ID Power Connector Term PWR* Bit 2 Bit 1 Bit 0 Bit 1 Bit 0 0 1 2 3 (Default) 4 5 6 *Term PWR is not used in HP workstation configurations. Figure A­8. [. . . ] Each user account contains the name the computer uses to identify the person (user ID), and the person's password. User accounts also contain project and organization names, to help the system determine who can use the system and what resources each person or organization can use. See also user ID, password. user ID The name the computer uses to identify you. Enter your user ID during the login procedure when the system displays the login prompt. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE HP VISUALIZE J5000 WORKSTATION




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual HP VISUALIZE J5000 WORKSTATION will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.