User manual HP PHOTOSMART R-SERIES DOCK

[. . . ] Connect the AC power adapter to the DC IN connector on the dock, plug the power cord into the AC power adapter, and plug the power cord into a wall outlet. If more than one power cord is in the box, use the cord that is appropriate for power outlets in your country. The AC power adapter for the dock is the same as the one used for your Rseries camera. If no power adapter came with your dock, use the one that came with your camera. [. . . ] The camera will turn on automatically. 11 3 Press the Save/Print button on the camera dock to start the print dialog. If you already selected images to print in the camera, the number of images selected will be shown in the Print Setup menu. 4 If all the settings in the Print Setup menu look correct, press the Menu/OK button on the camera or on the dock remote control to begin printing. Or, you can change settings in the Print Setup menu using the arrow keys on the camera or on the dock remote control, then press Menu/OK to begin printing. NOTE There is a print preview in the Print Setup screen showing the page layout that will be used for printing. This print preview updates as you change the settings for Print Size and Paper Size. 5 When the printing completes, you can leave the camera in the dock to recharge the camera battery. Displaying Images on a TV Using the Dock 1 Confirm the following: · The dock insert for your camera is attached to the top of the camera dock. (See step 1 on page 6. ) · The audio/video cable is connected between the camera dock and your TV, and the power cable is plugged into the dock. (See step 2 on page 7. ) 12 HP Photosmart R-series dock User's Manual TIP If you cannot locate video and audio input jacks on your TV to fit the connectors on the audio/video cable, you should be able to use the video and audio input jacks on a video cassette recorder (VCR) or DVD player connected to your TV. 2 Your camera is set to send either an NTSC or a PAL video signal to a TV, depending on the language you selected when you set up your camera. The NTSC format is used primarily in North America and Japan, and the PAL format is used primarily in Europe. If your TV accepts a different video signal from the default setting for your language, you must change the TV configuration setting in your camera. (See your camera User's Manual. ) 3 Your camera will be the source for the TV signal (just like a VCR or a camcorder), so you must set the TV to take video input from an external video source (your camera) instead of the antenna or cable TV. You can use the buttons to manually navigate through a slideshow of the images on the camera, or press to start an automatic slideshow of each image, playing any attached audio clip or video clip, and then changing to the next image. NOTE The Image Display on the camera turns off when the camera is connected to a TV, but you can still use the camera's menus because the menus will display on the TV screen. 13 Using the Remote You can use the dock remote control to pause the slideshow, magnify an image, rotate an image, select an image for HP Instant Share, or mark an image for printing. Before you can use the remote, you need to install the remote control battery. Remove the battery door on the back of the dock remote control and slide the round non-rechargeable CR 2025 battery into the remote, + (positive) side up, until it clicks into place, as shown in the picture. Then replace the battery door. 14 HP Photosmart R-series dock User's Manual Dock Remote Control Buttons 1 2 3 4 5 6 7 8 9 # 1 Button TV button Description Activates the TV connection and displays the first image in the camera on the TV (same as the TV button on the dock). To resume the slideshow, press this button again. 2 Play/Pause button 3 and These buttons work just like the arrow buttons buttons to buttons on your camera. The camera will not attempt to charge batteries that may be damaged or over-discharged. Remove the battery from the camera and charge it in the dock recharging bay, then try it in the camera again. If the battery will not charge sufficiently in either the dock or the camera, it is likely that the battery is bad. [. . . ] When recharging a lithium ion battery, do not cover the camera or the dock in any way. Do not operate the camera or the dock if it appears damaged in any way. 21 ! !Unplug the HP AC power adapter from the electrical outlet before cleaning. If it becomes difficult to insert the battery into or remove the battery from the camera or the dock, discontinue use of the battery and replace it with a new one. [. . . ]