User manual HALFORDS 2313

[. . . ] We recommend using Lithium batteries in temperatures below 32° F (0°C). · Turn off the camera before removing the batteries and the memory card. The card and the data may be damaged if the memory card is inserted or removed while the camera is still on. · Remove the batteries and memory card before storing the camera for long periods of time, then keep it in a well-ventilated place to prevent mould. [. . . ] Always upload video footage to your PC prior to replacing batteries to avoid memory loss Note: a) Battery installation should be done under adult supervision. c) Remove the batteries if the camera is not going to be used for long periods of time. This will save battery 11 life. d) Do not mix alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium) batteries. Only batteries of the same or equivalent type as recommended are to be used together. f) Rechargeable batteries are to be removed from the camera before being charged. g) Rechargeable batteries are only to be charged under adult supervision. Turning the Camera On Press and hold the for 2 seconds (two beeping sounds). For your safety, do not press any buttons on the camera during sports activities. The camera will be turned off automatically after 30 minutes of not being used unless it is in USB mode. 12 Note: If the camera is connected to your PC, you have to unplug the USB cable to turn off the camera. Inserting/Removing the SD memory Card Make sure the 2313 is turned off during the insertion or the removal of the SD card Warning: The card and the data may be damaged if the SD card is inserted or removed while the camera is on. Turn the SD card upside down (connect terminals facing up) then insert it carefully and completely. To use an SD memory card, turn off the 2313 and insert the SD memory card. When the camera is turned on again the SD card icon will be displayed on the LCD. If there is an error on the SD memory card, the SD card icon and the letters 'Err' will be displayed on the LCD. The SD card is equipped with a Write-Protect switch that can prevent writing and formatting to the card. The letters 'Err' will be displayed if the SD card is locked with Write-Protect switch. We recommend using SanDisk regular or SanDisk Ultra II SD cards. 21 22 Available Recording Time The available recording time is an approximation (these vary depending on the recording conditions and the type of card). Picture quality setting Internal Memory 32 MB VGA 30 fps 52 s VGA 15 fps QVGA 30 fps QVGA 15 fps QQVGA 30 fps 5 min QQVGA 15 fps 11 min 10 s VIII) Connecting to PC You can acquire recorded video footage from a PC by connecting the 2313 to the PC. "PC" appears on the 2313 LCD screen, which means 2313 is connected to your PC. *If you are connecting the camera to a PC for the first time, the required driver is installed automatically so that the camera can be recognized by Windows Plug and Play. Open the '100COACH' folder in the [DCIM] folder to start selecting your desired video files. · Folder Composition: Removable disk · Internal Memory · SD Memory Card DCIM 100COACH AVI_0001. avi 1 min 20 s 1 min 36 s 3 min 14 s 32 MB 64 MB 52 s 2 min 1 min 20 s 1 min 36 s 3 min 14 s 3 min 6 min 12 min 24 min 48 min 96 min 4 min 7 min 14 min 28 min 57 min 114 min 7 min 14 min 28 min 57 min 115 min 230 min 5 min 11 min 23 min 45 min 89 min 178 min 356 min 11 min 10 s 25 min 50 min 99 min 198 min 397 min 794 min SD Memory Card 128 MB 4 min 256 MB 8 min 512 MB 15 min 1 GB 2 GB 30 min 60 min 23 24 Note: 1. [. . . ] We encourage you to contact our Technical Support Team at atc@oregonscientific. com with any problems and/or suggestions, or, call our Customer Service Department at 1-800-853-8883. Please note that the Technical Support Team cannot issue or authorize any RMA's or replacements. For an RMA or replacement please contact our Customer Service Department. 28 Notes Oregon Scientific, Inc. 19861 SW 95th Avenue Tualatin, OR 97062, USA Hotline: 1-800-853-8883 Website: www. oregonscientific. com This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. [. . . ]