User manual GE SECURITY RANGER 8980E REV E

[. . . ] Bypass a sensor. 2 + Code + or 3 + Code + + Code + Sensor Number or Directly: Arm system silently. 5 + 2 + Code 5 + 3 + Code , 7+1 7+6 8 + Code + 2 8 + Code + 3 Check the system status. Initiate a sensor test. 3 GETTING TO KNOW YOUR SECURITY SYSTEM This manual describes how to operate your system. It describes basic arming and disarming commands as well as how to program system features. The dealer or installer may have already discussed the details of your system with you. [. . . ] Account Number Code Indicates 4-digits of account number XXXX Some pager providers transmit only numbers and not alpha-characters. If your account number contains alpha-characters, check with 14 LATCHKEY PAGING The Latchkey paging feature allows up to three pagerholders to be notified when the system is disarmed. This feature is useful when you're at work and would like to be notified when your daughter or son arrives home and disarms the system. Refer to the Appendix A User Sheets to see which pagers have been set up to receive a Latchkey page. Only Latchkey-designated user codes can cause a Latchkey page to be sent. If you'd like more user codes to be included, contact your installer. Preparing the system to send a Latchkey page: · Arm the system, then enter 6. Touchpads display briefly: "Pager on, " or "LATCHKEY PAGER ON. " USING THE PANEL DOWNLOAD FEATURE To download to the panel is to replace the old information in it with new information. Downloading is performed only by your dealer using ITI software specifically designed for this panel. Turning the Download feature on allows the dealer remote access to your panel in order to: · Update your account. · Allow your dealer to quickly implement requested programming changes. See "Troubleshooting" on page 16 for an explanation of the causes of trouble beeps and what you can do to fix the problem. Sensor Test This test verifies that the sensors in your system are operating correctly. The ability to conduct a sensor test is a code attribute given per User code. Check the Appendix A User Sheets to see which access codes have the ability to conduct a sensor test. Table 3. Enter Test Mode by pressing 8 + Code + 3. Touchpads display, "Press Status. System Armed to Sensor Test, " or "VSENSOR TEST nn MINUTES LEFT. " V When less than 5 minutes remain to the Test Mode time, the system sounds a short beep every 60 seconds. 2. Follow the test procedure for each device. Device Touchpads Test procedure Send a: Police panic alarm, Fire panic alarm, and Auxiliary panic alarm. Touchpad Result Touchpad Panic POLICE Touchpad Panic FIRE Touchpad Panic AUXILIARY POLICE PANIC OK FIRE PANIC OK AUXILIARY PANIC OK Zones nn OK Touchpad nn OK Touchpad Panic POLICE Touchpad Panic AUXILIARY POLICE PANIC OK AUXILIARY PANIC OK Zones nn OK SENSOR nn OK Zones nn OK SENSOR nn OK Zones nn OK SENSOR nn OK Zones nn OK SENSOR nn OK Zones nn OK SENSOR nn OK Zones nn OK SENSOR nn OK OK OK OK OK OK Wireless Touchpads Keychain Touchpads Press the Bypass key. Press and hold the two assigned panic buttons simultaneously for 3 seconds. Panic buttons Door/window sensor Smoke detector Motion detector Rate-of-Rise Heat Detector (Not UL investigated) Shock sensor (Not UL investigated) Press and hold the appropriate panic button(s) for 3 full seconds. Press and hold the test button until the system sounds transmission beeps. Avoid the motion detector's view for 5 minutes, then enter its view. Rub your hands together until warm, then place one hand on the detector for 30 seconds. Wait at least 30 seconds before testing again. 16 Device Glass guard sensor (Not UL investigated) Freeze sensor (Not UL investigated) Test procedure Tap the glass 3 or 4 inches from the sensor. Touchpad Result Zones nn OK SENSOR nn OK Zones nn OK SENSOR nn OK · If you need more time to complete testing, restart the timer by pressing 8 + Code + 3. [. . . ] The telephone company may ask you to disconnect this equipment from the network until the problem has been corrected or until you are sure that the equipment is not malfunctioning. This equipment may not be used on coin service provided by the telephone company. Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines, and internal metallic water pipe system, if present, are connected together. Caution: Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate. [. . . ]