User manual GARMIN GNC 250
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual GARMIN GNC 250. We hope that this GARMIN GNC 250 user guide will be useful to you.
You may also download the following manuals related to this product:
GARMIN GNC 250 PILOT'S GUIDE (739 ko)
GARMIN GNC 250 Quick Reference (193 ko)
GARMIN GNC 250 QUICK REFERENCE GUIDE (193 ko)
Manual abstract: user guide GARMIN GNC 250
Detailed instructions for use are in the User's Guide.
[. . . ] OWNER'S MANUAL & REFERENCE
ACTV
STBY
GNC 250
CLR
ENT
CRSR
SQ
NRST
RTE
WPT
NAV
MSG
GNC 250 's Guide Pilot
®
TM
INTRODUCTION
Foreword
Software Version 2. 06 or above
© 1995 GARMIN International 9875 Widmer Road, Lenexa, KS 66215, USA Romsey House, Station Approach Romsey, Hampshire, UK S051 8DU All rights reserved. No part of this manual may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, for any purpose without the express written permission of GARMIN.
GARMINTM, GNC 250TM, Spell'N'FindTM, AutoLocateTM, MultiTrac8TM, GPSCOMTM and AutoStoreTM are trademarks of GARMIN and may only be used with permission. NavData® is a registered trademark of Jeppesen Sanderson, Inc.
Information in this document is subject to change without notice. GARMIN reserves the right to change or improve their products and to make changes in the content of this material without obligation to notify any person or organization of such changes or improvements.
All rights reserved.
October 1995
190-00067-50 Rev. [. . . ] A status will appear when it is the active-to waypoint, part of an active or stored route or a proximity waypoint. To edit, rename or delete waypoints, the cursor must highlight the desired waypoint.
To highlight a waypoint: 1. Press E on the confirmation page to change the name, or press \ to cancel. User Waypoint List
SECTION
3
Waypoint Comments
REFERENCE WPT KEY CPA Diagram
The last page available through the GNC 250's WPT key is the waypoint comments page, which lists all waypoints that have a user comment. User comments may be added to 250 waypoints stored in the user or NavData® database, and allow you to note two lines of special information concerning a particular waypoint.
To enter user comments: 1. Enter the waypoint identifier from any waypoint page (see page 35), and press C to remove the flashing cursor. Press E to accept, and repeat steps 4 and 5, if necessary, to enter information on another line.
Entering waypoint comments.
6. Use K to scroll through the list.
Waypoints with Comments List
The GNC 250 will display the waypoints with comments in alphabetical order, up to six waypoints at a time. The scrolling arrow prompt will indicate which direction to scroll to view additional waypoints.
To view comments for a selected waypoint: 1. Rotate O to display any other available pages for the selected waypoint.
The GNC 250's extensive waypoint database makes it possible for several waypoints to share the same identifier. To ensure that you are selecting the waypoint desired, the GNC 250 will always offer the waypoint confirmation page (which shows the waypoint's position) when an identifier is entered for a particular function.
To accept the waypoint position: 1. Press \ with the cursor over the `ok?' prompt.
REFERENCE WPT KEY
Search and Rescue Waypoint Confirmation Operations Duplicate Waypoints
SECTION
3
Once a waypoint has been accepted or rejected, the previous page will be displayed. If there is more than one waypoint available for a selected identifier, the GNC 250 will display a duplicate waypoint page for you to choose the desired waypoint. The waypoint identifier and number of duplicates will be shown at the top of the page, with the waypoint type and region of each duplicate indicated below. The waypoints listed are sorted by the distance from your present position.
To scroll through additional duplicate waypoints: 1. Rotate O with the flashing cursor active, or K with the flashing cursor inactive. Activate the flashing cursor and rotate O to highlight the desired waypoint. Press E over the `ok?' prompt to accept the waypoint or \ to reject the waypoint and return to the duplicate waypoints list.
Waypoint Confirmation Page
Duplicate Waypoints Page
51
SECTION
REFERENCE WPT KEY
User Comments & Locked Waypoints Parallel Track Waypoint Scanning
3
Because the GNC 250 relies on a NavData card for most waypoint information, there may be instances when waypoint information is not available for use. Locked waypoints exist when a waypoint contained in a route or used as a proximity waypoint is not contained on the NavData card, or no card is inserted in the unit. If this condition exists, you'll be alerted with a `Proximity wpt locked', `Route wpt locked' or `Wpt comment locked' message when the unit is powered up. The identifier of a locked waypoint will be replaced with a `lockd' message, which indicates you cannot obtain waypoint information or navigate to the waypoint. The identifier of a locked waypoint may be displayed by highlighting `lockd' and pressing ENT. [. . . ] Remote XFR key stuck - The remote XFR key is stuck in the `pressed' state. Check the installation.
MESSAGES & ABBREVIATIONS
SECTION
D
ROM failed
Route is empty Route is full
Route wpt deleted
Route wpt locked
Route wpt moved
- The GNC 250 has detected a failure in its permanent memory. If this message occurs, the unit is unusable and should be taken to an authorized GARMIN service center. - One or more route waypoints were deleted while receiving data from the optional PC150 Interface Kit. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE GARMIN GNC 250
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual GARMIN GNC 250 will begin.