User manual FISHER & PAYKEL GWL15

[. . . ] Washer should not be installed on rugs or exposed to the weather. Washer end of hose Lid Clearance Standpipe Height 33 1/2" to 78" Faucet end of hose HAVE YOU CARRIED OUT THE FOLLOWING INLET HOSE CONNECTIONS Faucet end of hose SPECIFICATIONS PULL HOSE THROUGH GUIDE 3/4" (20mm) PLUMBING Bottom packer MUST be removed from the base of the washer, before the basket packer is removed. Filter end must be connected to faucet. Water Temperature Your cold water should not exceed 95°F (35°C) or your hot water exceed 150°F (65°C). Temperatures above this may damage your washer. HEIGHT The drain hose guide MUST be fitted to the drain hose and should not extend more than 3/4" (20mm) from the end of the guide. Place the drain hose in tub or standpipe. Washer end of hose. Shut off valves LEVELING Make sure washer is level and four rubber inserts are properly installed. GROUNDING MUST be properly grounded to conform to local codes and ordinances. [. . . ] Check with a qualified electrician or serviceman if you are in doubt as to whether the appliance is properly grounded. OPERATION 1. Turn faucets on. Check for leaks, noise, vibration, correct water temperatures and proper operation in spin. 2. Turn hot and cold water faucets off and instruct customer to do the same when washer is not in use. Give customer the Use & Care Book and Installation Instructions. Both hot and cold shut-off valves (faucets) should be available in laundry area. Drain Water may be drained into a standpipe or set tub. The standpipe must be 11/2" (38mm) minimum inside diameter and must be open to the atmosphere. Allow for adjustable feet WIDTH DEPTH Inlet water pressure Max 150 psi (1MPa) Min 3 psi (20kPa ) All models 251/2" (650mm) 251/2" (650mm) 1/2"- 411/2" (1020-1050mm) 40 551/2"- 561/2" (1410-1440mm) ELECTRICAL This appliance must be supplied with 110V-120V, 60Hz, and connected to an individual, properly grounded branch circuit, protected by a 15 or 20 amp circuit breaker or time delay fuse. DIMENSIONS MODEL DEPTH WIDTH HEIGHT to top of console HEIGHT LID OPEN READ AND OBSERVE ALL SAFETY INSTRUCTIONS - CONSULT THE PRODUCT USE & CARE BOOK FOR CUSTOMER CAUTIONS Specification subject to change without notice P/N 420264A Specification subject to change without notice STEP 1 REMOVE BOTTOM PACKER 1. Tilt the machine backwards and walk the machine off the bottom packer. The plastic bottom packer can now be removed from the machine. STEP 3 Drain Hose 1. Carefully pull the drain hose out from the back of the washer by pulling the exposed part of the hose downwards and then out. Do not modify the plug provided with the appliance - if it will not fit the outlet, have a proper outlet installed by a qualified electrician. STEP 5 LEVELING THE WASHER Leveling Feet 1. Insert the four rubber leveling feet inserts into the feet on the base of the washer. INCORRECT ADJUSTMENT Caution: Operating the machine when the bottom packer is in place can result in damage to the machine. PULL HOSE THROUGH GUIDE 3/4" (20mm) STEP 2 REMOVING BASKET PACKER AND ACCESSORIES 1. 2. Keep the bottom packer and basket packer in case they are required for future transit. Remove hoses, accessories and installation pack. 3. Place the drain hose in laundry tub or standpipe. Note: · In multi-storey apartments or any upper floor, the machine should be installed on a drained floor · Check that the tub or standpipe is free from lint or other obstructions. Visually check that the lid and topdeck are aligned. OPERATION 1. Turn faucets on. Check for leaks, noise, vibration, correct water temperatures and proper operation in spin. Turn hot and cold water faucets off and instruct customer to do the same when washer is not in use. [. . . ] Turn hot and cold water faucets off and instruct customer to do the same when washer is not in use. 3. Give customer the USE & CARE Book and Installation Instructions. 2. We suggest a minimum clearance of 1" (25mm) on each side for ease of installation. 1" (25mm) 1" (25mm) If it does not look like the diagram below, adjust one of the front feet slightly until it matches. The installation pack contains the following: · 4 rubber inserts for the leveling feet · 1 drain hose guide STEP 4 Inlet Hoses 1. Install hoses with straight end (with filters) onto the faucets. [. . . ]