User manual ELECTRO-VOICE RE16 EDS

[. . . ] SPECIFICATIONS Element: Dynamtc Frequency Response: 80-l 5, 000 Hz Polar Pattern: Super-cardioid Impedance: Lo-Z (150 ohms nominal) Output Level: -56 dB (0 dB = 1 mW/lO dyneslcmz) EIA Sensitivity Rating: -150 dB Hum Pickup Level: - 125 dBm (re: , 001 gauss field) Diaphragm: Electra-Voice Acoustalloy Case Material: Steel Dimensions: 187. 3 mm (7. 38 tn. ) long 45. 2 mm (1. 78 in. ) dtameter 19. 1 mm (0. 75 in. ) shank diameter Finish: Fawn beige micomatte Net Weight: 227 g (8 oz), not including cable Cable: 4. 6 m (15 ft), two-conductor, shielded, broadcast-type cable, rubber-jacketed with Switchcraft A3F connector Accessories Furnished: Model 310A stand adapter Zippered vtnyl pouch Optional Accessories: 307 suspension shock mount 312A stand adapter 313A shock mount 340 security clamp 381 swdch/connectorassembly 400, 422 or 423A desk stand DESCRIPTION AND APPLICATIONS The Electro-Voice Model RE16 IS a Variable-D dynamic supercardioid microphone designed for the most exacting professional use. The blast filter, an integral part of the RE16, permits hand-held and outdoor use without " P-popping" or excessive wtnd noise. [. . . ] Attenuation at frequencies from 100 to 4, 000 Hz (referred to major axis signal value) shall exceed 25 dB at 150 deg. Attenuation at 180° from major axis at frequencies from 100 to 4, 000 Hz shall exceed 15 dB. Attenuation above 4, 000 Hz shall exceed 12 dB Polar characteristics shall be suffrcrently uniform in all planes so that rt IS, effectively, a supercardiold of revolution. A hum-buck coil shall be provided in senes with the microphone element. The hum-buck coil shall decrease hum prckup by at least 25 dB. | , ROLL-OFF FIGURE 1 - Frequency Response FLAT FIGURE 2 - Dimensions MARKED GREEN HEAD TERMINAL HUM BUCK COIL 1coSCALE IS 5 DEClBELS PER Dl"lSlON POSITIVE PRESSURE ON GENERATING ELEMENT CAUSES POSITIVE VOLTAGE ON RED CABLE LEAD FIGURE 3 - Polar Response FIGURE 4 - Wiring Diagram An Integral passive filter network shall be provided such that when filter switch IS In " posrtlon, low-frequency response shall on" be so deviated from " flat" response that a fall of 6 dB from 1, 000 to 100 Hz shall be effected. With switch In " off" posItIon, microphone shall be essentially " flat"from 100 to 1. 500 Hz. wtth a 6 dB nse in response from 50 to 100 Hz, and a 2 dB rise occurring at 2, 000 Hz extending to 12, 000 Hz. Output level shall be -56 dB (0 dB= 1 mW/lO dynes/cm*), and EIA sensitivityrating shall be - 150 dB. The diaphragm shall be non-metallic Acoustalloy and shall have a shield to prevent dust particles from reaching the diaphragm The case shall be made of steel. with 19. 1 mm (75 in. ) diameter shank, and a maximum length of 187. 3 mm (7. 38 In. ), not lncludtng cable connector Flnlsh shall be fawn beige mcomatte. [. . . ] and you may also have other rights which vary from state to state. Service and repair address for this product: Electro-Voice, Inc. , 600 Cecil Street, Buchanan, Michigan 49107. Specifications subject to change without notice. ELECTRO-VOICE, INC. , MANUFACTURING PLANTS AT l 600 Cecil Street, Buchanan, Mlchlgan 49107 SEVIERVILLE, TN n OKLAHOMA CITY, OK n BUCHANAN. MI m NEWPORT TN n Electro-Voice. Inc I990 n LItho In USA Part Number 530252-538 [. . . ]