User manual ELECTRO-VOICE FRX+660PI EDS

[. . . ] FRX+660/FRX+660PI 15-Inch Two-Way Horn-Loaded 60° x 60° Coaxial Speaker System Key Features: · · · · · · · · · Pattern Control to 500 Hz 60° x 60° coverage Built-in L-track rigging Available in black, white and unfinished Passive or bi-amp operation High sensitivity, 105 dB Ring-Mode Decoupling / RMDTM Full Coaxial Design Weatherized Version Available (FRX+660PI) General Description: FRX+ series is designed for applications in highly reverberant spaces where excellent directivity control down to 500 Hz is critical. [. . . ] A 300W line transformer is available as a contractor installed item. Technical Specifications: Freq. Range1 (-10 dB): 52Hz-16kHz Max Calculated SPL: 133 dB Horizontal Coverage: 60° Ver tical Coverage: 60° LF Power Handling: 400W Continuous, 1600W Peak HF Power Handling: 60W Continuous, 240W Peak Passive Power Handling: 400W Continuous, 1600W Peak LF Sensitivity (Bi-Amp): 105 dB, 1W/1m HF Sensitivity (Bi-Amp): 109 dB, 1W/1m Passive System 105 dB, 1W/1m Sensitivity: Impedance: 8 ohms (Nominal), 7. 2 ohms (Min. ) LF Transducer : DL15X 15" (381mm) Driver, 8 ohms HF Transducer : DH2t 2" (51mm) Diaphragm Comp. Driver, 8 ohms Passive Crossover 1350 Hz Frequency: Connectors: Two barrier strips Enclosure Material: 13-ply Birch plywood Grille: 16 GA steel (PI Version Stainless Steel) Environmental Spec: IEC 529 IP24, (PI Version IP44) MIL STD 810 Transformer : See Page 4 Dim (H x W x D): 31. 0" x 28. 3" x 26. 0" (787 x 719 x 660 mm) Net Weight (each): 152 lbs (69. 0 kg) Shipping Weight: 157 lbs (71. 2 kg) 1 Full Space measurement. Half Space use will improve LF response. FRX+660/FRX+660PI Full Range Loudspeaker Frequency Response (Full Space): Impedance: Beamwidth: Horizontal Off Axis Frequency Response: Directivity: Vertical Off Axis Frequency Response (up/down): Block Diagram: Engineering Data Sheet Horizontal 1/3 Octave Polars: Vertical 1/3 Octave Polars: Dimension Drawings: Top View Front View Side View Line Transformer Kit: Part number 301401-000 transformer kit is available to mount internally to any FRX+ System. The kit includes a special 300 Watt line transformer for operating on 70, 100, and 140 volt distributed line systems, wiring harness, instructions, and hardware. At 300 Watts it has a bandwidth of 35 Hz to 15 kHz ±1dB. FRX+660 Part Numbers · · · 301237-000 - Unfinished 301237-001 - Black 301237-002 - White FRX+660PI Part Numbers · 301395-001 - Black Architectural & Engineering Specs: The loudspeaker system shall be a coaxial, two-way full range design consisting of a 15-inch woofer, a high-frequency compression driver on a molded constant-directivity horn and a dividing network providing an acoustic crossover frequency of 1, 350 Hz. The system shall be configurable in a biamp mode by moving a single connector in the crossover network. The loudspeaker shall meet the following performance criteria; power-handling, 400 watts, based upon ANSI/EIA RS-426-A 1980 standard for full-range loudspeaker systems; frequency response, smooth and usable at high SPL levels from 60 Hz to 15 kHz; pressure sensitivity, 104 dB SPL (passive mode) or 105 dB (LF)/109 dB (HF) in biamp mode for 1W at 1m; impedance, 8 ohms nominal, 7 ohms minimum. [. . . ] For customer orders, contact Customer Service at: + 1 952 884-4051 Fax: + 1 952 736-4212 For warranty repair or service information, contact the Service Repair department at: 800/685-2606 For technical assistance, contact Technical Support at: 866/78AUDIO Specifications subject to change without notice. 12000 Portland Avenue South, Burnsville, MN 55337 Phone: 952/884-4051, Fax: 952/884-0043 www. electrovoice. com © Telex Communications, Inc. [. . . ]