User manual ECS P4VXADP10A

[. . . ] Preface Copyright This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author. Version 1. 0a Disclaimer The information in this document is subject to change without notice. The manufacturer makes no representations or warranties with respect to the contents hereof and specifically disclaim any implied warranties of merchantability or fitness for any particular purpose. [. . . ] However, we recommend that you read this chapter in case you need to make any changes in the future. This Setup Utility should be used: · · · · · when changing the system configuration when a configuration error is detected and you are prompted to make changes to the Setup Utility when trying to resolve IRQ conflicts when making changes to the Power Management configuration when changing the password or making other changes to the Security Setup 28 Entering the Setup Utility When you power on the system, BIOS enters the Power-On Self Test (POST) routines. After the POST routines are completed, the following message appears: Press DEL to enter SETUP Pressing the delete key accesses the BIOS Setup Utility: Phoenix ­ AwardBIOS CMOS Setup Utility Standard CMOS Features Advanced BIOS Features Advanced Chipset Features Integrated Peripherals Power Management Setup PnP/PCI Configurations PC Health Status Esc : Quit F10 : Save & Exit Setup Frequency/Voltage Control Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor Password Set User Password Save & Exit Setup Exit Without Saving : Time, Date, Hard Disk Type . Select Item BIOS Navigation Keys The BIOS navigation keys are listed below: Key Esc +/­/PU/PD F10 F1 F5 F6 F7 Function Exits the current menu Scrolls through the items on a menu Modifies the selected field's values Saves the current configuration and exits setup Displays a screen that describes all key functions Loads previously saved values to CMOS Loads a minimum configuration for troubleshooting. Loads an optimum set of values for peak performance Updating the BIOS You can download and install updated BIOS for this mainboard from the manufacturer's Web site. New BIOS provides support for new peripherals, improvements in performance, or fixes for known bugs. If your mainboard has a BIOS protection jumper, change the setting to allow BIOS flashing. 29 2. 3. 5. 6. If your mainboard has an item called Firmware Write Protect in Advanced BIOS features, disable it. (Firmware Write Protect prevents BIOS from being overwritten. ) Create a bootable system disk. (Refer to Windows online help for information on creating a bootable system disk. ) Download the Flash Utility and new BIOS file from the manufacturer's Web site. Turn off your computer and insert the system diskette in your computer's diskette drive. (You might need to run the Setup Utility and change the boot priority items on the Advanced BIOS Features Setup page, to force your computer to boot from the floppy diskette drive first. ) At the A:\ prompt, type the Flash Utility program name and press <Enter>. You see a screen similar to the following: FLASH MEMORY WRITER V7. 33 (C) Award Software 1999 All Rights Reserved For (MAINBOARD NAME) DATE: 10/26/2000 Flash Type File Name to Program :____________________ Error Message 7. 8. Type the filename of the new BIOS in the "File Name to Program" text box. When the installation is complete, remove the floppy diskette from the diskette drive and restart your computer. If your mainboard has a Flash BIOS jumper, reset the jumper to protect the newly installed BIOS from being overwritten. Using BIOS When you start the Setup Utility, the main menu appears. The main menu of the Setup Utility displays a list of the options that are available. When an option is highlighted, execute the option by pressing <Enter>. Some options lead to pop-up dialog boxes that prompt you to verify that you wish to execute that option. Some options (marked with a triangle ) lead to submenus that enable you to change the values for the option. Submenu items are denoted by a triangle . 30 Standard CMOS Features This option displays basic information about your system. Phoenix ­ AwardBIOS CMOS Setup Utility Standard CMOS Features Date (mm:dd:yy) Time (hh:mm:ss) IDE Primary Master IDE Primary Slave IDE Secondary Master IDE Secondary Slave Drive A Drive B Floppy 3 Mode Support Video Halt On Base Memory Extended Memory Total Memory : Move Enter : Select F5:Previous Values Tue, July 11 2001 12 : 8 : 59 Item Help Menu Level Change the day, month, year and century. [1. 44M, 3. 5 in. ] [None] [Disabled] [EGA/VGA] [All Errors] 640K 31744K 32768K +/-/PU/PD:Value: F10: Save ESC: Exit F1:General Help F6:Fail-Safe Defaults F7:Optimized Defaults Date and Time The Date and Time items show the current date and time on the computer. If you are running a Windows OS, these items are automatically updated whenever you make changes to the Windows Date and Time Properties utility. IDE Devices (None) Your computer has two IDE channels (Primary and Secondary) and each channel can be installed with one or two devices (Master and Slave). [. . . ] Before installing the software from Windows Explorer, look for a file named README. TXT, INSTALL. TXT or something similar. This file may contain important information to help you install the software correctly. Some software is installed in separate folders for different operating systems, such as DOS, WIN NT, or WIN98/95. To install the software, execute a file named SETUP. EXE or INSTALL. EXE by double-clicking the file and then following the instructions on the screen. [. . . ]