User manual EARLEX STEAM DYNAMO PRO

[. . . ] Instant Steamer ­ Model IS2000 USER INSTRUCTIONS PLEASE READ THESE INSTRUCTIONS CAREFULLY BEFORE USE Thank you for purchasing an Earlex Instant Steam Cleaning Kit. In order to obtain the best results from this product, please read these instructions & make a special note of the Safety Rules before commencing any work. EARLEX INC. WILL ACCEPT NO RESPONSIBILITY FOR THE USE OF THIS PRODUCT IF USED FOR ANY OTHER PURPOSES THAN THOSE DETAILED HEREIN RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE HELPLINE NUMBER - TOLL FREE 888 STEAM 12 CONTENTS Important Information Check that your Steam Dynamo Pro is complete Safety Rules Safety Precautions Steam Cleaning Delicate materials About your Earlex Steam Dynamo Pro Features Guide Preparing your Steam Dynamo Pro for use Using the main attachments Using the mini attachments Getting started Cleaning & maintenance Storing the unit Trouble Shooting Spare parts Mains connection Warranty 3 4 4 4 5 7 8 9 11 12 13 13 14 14 15 16 BEFORE PROCEEDING ANY FURTHER PLEASE CHECK THAT YOUR EARLEX STEAM DYNAMO PRO IS COMPLETE. HELPLINE NUMBER - TOLL FREE 888 STEAM 12. CALL FIRST IF YOU HAVE ANY PROBLEM 2 OPENING THE CARTON When you open the carton, you will see the Caddy unit, which has the 4 main attachments stowed inside. [. . . ] As the attachment is moved down the window (mirror or tiles) and the Steam Release Button is pressed, the rubber blade will clean away the dirt as it wipes the surface after the steam has been applied. After you have completely finished cleaning, release the Steam Button and clean the surface from top to bottom with the rubber blade only. Excess water from around the window sould be removed with a dry cloth. Steam will completely remove dust, film or greasy marks from windows, mirrors, tiles and patio doors. It will remove soap and grease residues but cannot remove deposits of scale. To remove black marks from grouting or difficult corners use the mini attachments, Jet Nozzle, Brush Nozzle or Scraper Nozzle. Upholstery Cleaner/Garment Steamer (29) IMPORTANT ­ Some upholstery, fabrics and soft furnishings have stain resistant treatments, which, may be affected by steam cleaning. Try cleaning a small area of material that is normally unseen, then allow 24 hours before checking whether there have been any unusual effects on the material. You only require a small amount of steam to clean, and soaking can leave water marks or cause bleed through linings etc. The Upholstery Cleaner can be used either with or without the Bonnet (32). For normal cleaning purposes and for general use the Bonnet would be fitted. When removing creases from garments and hanging drapes you can sometimes improve the appearance of the material by using the head without the Bonnet attached. This tool can also be used either fitted directly onto the Hose Handle or fitted to one or both Extension Tubes. First select which is best for the task in hand and assemble together. HELPLINE NUMBER - TOLL FREE 888 STEAM 12. CALL FIRST IF YOU HAVE ANY PROBLEM 10 Fitting the Bonnet (32) to the Upholstery Cleaner (29) Take the Bonnet, place it on a flat surface with the strings at the top and the nap facing outwards and place the Upholstery Cleaner in the middle. Pull the string until the Bonnet fits tightly to the Upholstery Cleaner, and tie with a bow. When cleaning upholstery you will need to glide the head across the material in the same way as when using the Floor Cleaner. Do not use bleach or fabric conditioner and use only one third of normal soap powder to avoid clogging the fibres. Spare Bonnets can be purchased from Earlex Inc or you can make your own using Terry Toweling material. The Upholstery Cleaner can also be used very effectively for removing the creases from hanging drapes. Upholstery Cleaner/Garment Steamer To set up your Steam Dynamo Pro as a Garment Steamer proceed as follows:In the Plug Storage Recess (22) there is a socket (23) to accept the button end of the Extension Tubes. Fit the Extension Tubes together and then locate both into this socket. [. . . ] c) Slide the Steam Unit into the center of the Caddy until the yellow Steam Unit Release Latch, locks into place. d) Take the Power Cord, and coil it tightly around the base of the Steam Unit so that after 41/2 turns the plug can be stored in the front recess. Then coil the hose 11/2 turns until the Handle parks into it's Holster. Press down the Handle Release Button and push the Handle into the Holster so that the release button locks into its docking aperture. [. . . ]