User manual EAGLE ACCUMAP 12

[. . . ] AccuMap 12 INSTALLATION AND OPERATION INSTRUCTIONS TM ® Copyright © 1996, 1997 Eagle Electronics All rights reserved. AccuMap 12TM is a trademark of Eagle Electronics EagleTM is a registered trademark of Eagle Electronics IMS SmartMapTM is a trademark of Lowrance Electronics, Inc. A CAREFUL NAVIGATOR NEVER RELIES ON ONLY ONE METHOD TO OBTAIN POSITION INFORMATION. The background map built into this unit is not intended for navigation and its accuracy has not been verified. [. . . ] To turn the alarm on, press the MENU key, then select the "CLK ALM" menu. When the alarm goes off, an audible tone sounds along with a flashing message on the screen. In other words, if you set the alarm to go off at 7:00 a. m. , then the AccuMap 12 will have to be on at 7:00 a. m. , also. The count-up timer starts at zero and counts up to the time you entered. To set either timer, first switch to a screen that is showing the timer that you want to use. A screen similar to the one below appears. 27 Using the right and left arrow keys, move the black box to the first number in the time that you want to set. (The time is in hours, minutes, and seconds) Now press the up or down arrow keys until the desired number shows. Continue until the time shown in the display is correct, then press the ENT key. To start the timer, press the MENU key, then move the black box to the "Dn Timer STOP/ GO" label. If you turn the up timer's alarm on (press the right arrow key when the black box is on the (Up ALM. . . Off/On label), it will sound a tone when it reaches the time you entered in the up timer set menu. You can reset either alarm to the time you originally set by pressing the MENU key, then moving the black box to either the "Up Timer Reset" or "DN Timer Reset" label, then press the right arrow key. REPROGRAM BOXES The digital boxes on the MAP 3 and NAV 1 screens can be reprogrammed. The changes you make to the screen will remain in memory, even if all power is removed from the unit. You can, however, return the boxes to the factory settings from the "Preset Groups" item in the "System Setup" menu. To customize a screen, first switch to either MAP 3 or NAV 1, whichever you want to customize. Next, press the MENU key, then press the up or down arrow key until the "Reprogram Boxes" menu is highlighted. The screen shown as number two at the top of the next page appears. 28 REPROGRAMMING BOXES 1. 3. SELECT "REPROGRAM BOXES" FROM MAIN MENU. THE BOX SELECTION SCREEN APPEARS. PRESS THE RIGHT ARROW KEY UNTIL THE DESIRED BOX APPEARS. THIS IS THE FIRST WINDOW THAT WE WANT TO USE. PRESS THE UP ARROW KEY TO SELECT IT. 4. 5. 6. THE FIRST BOX IS PLACED AT THE TOP. AFTER MESSAGES ERASE THEMSELVES, YOU'RE RETURNED TO THE BOX SELECTION SCREEN SHOWN IN STEP 2. WE CHOSE THIS WINDOW AS THE SECOND ONE FOR THIS GROUP. REPEAT STEPS 2 AND 3 AGAIN. "vOLTS" IS THE LAST BOX CHOSEN FOR THIS SCREEN. 7. 8. See the back of this manual for a complete listing of all box options. THIS MESSAGE APPEARS AFTER THE LAST BOX IS SELECTED . IT AUTOMATICALLY ERASES. THE FINISHED SCREEN. 29 The first window appears on this screen. [. . . ] We reserve the right to make changes or improvements in our products from time to time without incurring the obligation to install such improvements or changes on equipment or items previously manufactured. This warranty gives you specific legal rights and you may also have other rights which may vary from state to state. Your remedies under this warranty will be available so long as you can show n a reasonable manner that the defect occurred within one (1) year fro the date of your original purchase, and we must receive your warranty claim no later than 30 days after such 1-year period expires. Your claim must be substantiated by a dated sales receipt or sales slip. 64 How to Obtain Service (Canadian Customers Only) We back your investment in quality products with quick, expert service and genuine Eagle replacement parts. [. . . ]