User manual DRAPER 88069

[. . . ] 5 Data security and radiation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2. 2 Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Introduction of the hardware. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Install the hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Green: HOMEPLUG Physical data rate > 100Mbps B HOMEPLUG Link/Activity LED Green + Red b. Red: 0 < HOMEPLUG Physical data rate < 40Mbps LED blinking (0. 06 sec ON / 0. 06 sec OFF)— HOMEPLUG data traffic a. Red: 0 < HOMEPLUG Physical data rate < 40Mbps Steady Green: WiFi active under security protection, C WiFi & Security LED Green + Red Flash Green: WiFi transmits packets under security protection, Steady Red: WiFi active under NO security protection, Flash Red: WiFi transmits packets under NO security protection, OFF: when WiFi is disabled Green ON: When in router mode (factory default is AP Bridge mode) D Operation mode LED, Green + Red Green OFF: Bridge (AP) mode. Red Flash: WPS activity Red OFF: No WPS activity R 7|Page Table 2 – push button definition Position Push button name Behavior Press 1 to 5 seconds – switch WiFi OFF/ON. Factory default is WiFi ON Symbol E WiFi Setting button Press > 5 seconds – switch Router mode ON /OFF. When pressing the button, the operation mode LED will flash once per second. Please keep pressing for 5 LED ON-and-OFF, then release the button after the LED fast blink with red color. during the WPS procedure, LED blinks red for 2. 5 minutes then stop automatically. WPS F Press 1. 5 to 4 seconds - start or stop Security key exchange When press and release the button for 1. 5 to 4. 0 seconds, this will enter Security key exchange procedure. In this procedure, the device starts joining into a logical network of other device or announcing its network G GROUP/Pairing for other devices to join. This procedure automatically stops after two minutes or until user press this button 1. 5 to 4 sec again. Press over 10 seconds - Generate random security key When continuous press is or over 10 sec, all LED light OFF and ON once to inform users a new random key has been generated so that users can release the button. To exit standby, just insert the Ethernet cable to the Homeplug, or wake up the connected device. Note: Some computers support the Wake on LAN function that may cause the Homeplug not to enter the standby mode. 16 | P a g e 7. Type http://192. 168. 0. 234 in the address bar and press [Enter] 17 | P a g e 3. Type user name and password (default username is ‘admin’, the password can be found on the backlabel of the 88069). 4. Click OK. 5. You will see the home page of the 88069. The System status section allows you to monitor the current status of your 88069 the UP time, hardware information as well as firmware version information is displayed here. 18 | P a g e Basic Setup Wizard The setup Wizard can help you to setup the device with minimum setting. Open the page in the left panel and click “Next” button in the welcome page. In the next page, choose the device to be “Access Point” mode or “Router” mode. Choosing each mode will have the respect setting pages like the figure below. Please refer to the pages in the next section for the explanation of each setting. In the final step of setting, click “Finish” button and the device will reboot to apply the settings. 19 | P a g e System settings This device supports two operation modes for the IP network. Click to select one between the following two wireless operation modes, then push the “Apply” button. Item Operation mode: Access Point Operation mode: Router Time Zone Daylight Saving Admin Username Admin Password Confirm Password Description This device acts as Wireless Access Point (AP) to provide WLAN service and bridge it to wired connection. This device acts as Wireless Access Point to provide WLAN service and router to connect LAN/WLAN to the Internet. If password is entered in the above field, enter it again here to confirm. 20 | P a g e Lan Settings Setup the LAN settings for LAN interface. Item IP Address Subnet Mask Default Gateway DHCP Server Description Setup the IP Address for the LAN interface. [. . . ] Select “Not Configured” and the WLAN client which is setup “Registrar” type of WPS will transfer Wi-Fi setting to this AP device in the WPS-PIN process, and then this device will apply the new setting from this WLAN client. WPS Method Select PBC (Push Button Configuration) or PIN (Personal Identification Number) as the method. For PIN method, find the PIN code in the utility of the WLAN client connecting to this AP, and then enter it in the PIN field. The Wi-Fi link between the WLAN client and the device should be encrypted. If the above settings are configured, press “Start” button to begin. Station PIN WPS Status Device PIN It shows the current PIN number of this device. [. . . ]