User manual DOD ENVELOPEFILTER440

[. . . ] Laser Ray Button Pressing and holding the button, the red dot projected is the area which is being recorded; it is used for adjusting the installation position of the drive recorder. 3. 14 4. Halt recording / USB switch Pressing and holding for 2~3 sec. , the red light will stop blinking and become constant indicating recording stopped. Pressing and holding again for 2~3 sec. , red light will start blinking again and recording will continue. Connect the drive recorder to the computer with USB cable, and press for 2~3 sec. Format -Format Button Pressing and holding for 2~3 sec. , the red and blue lights will start blinking simultaneously indicating formatting. [. . . ] Reset - Forced Shutdown Button Press the RESET button if crash occurred owing to improper operation. The drive recorder will be forced to shut down and all indicator lights will be switched off. Plugging the power out and in again will resume recording. 15 Menu Operation Transmit the video to the monitor (Page12, 13) before proceeding to menu operation, and use the remote controller to operate (Page08). Image Param Video resolution Video resolution can be configured during recording. Higher value means higher resolution and better picture quality, and the storage capacity consumption will be relatively higher. Remove Controller MENU ButtonImage ParamMenuVideo resolution1920x1080 30P*/1440x1080 30P/1280x720 30P/848x480 60P/848x480 30P/640x480 30P *Setting Value 16 Scene Scene setting can be done to allow shooting to be more conformed to the surroundings and achieve optimum shooting effect. Select [AUTO] to allow the recorder to choose the setting automatically. Remove Controller MENU Button Image Param Menu Scene AutoNight Portrait Night Scenery Sports Landscape */ / / / /Portrait/Sunset *Setting Value 17 Digital effect This effect produced by this setting can achieve certain playfulness, and changes in color are more apparent. Remote Controller MENU ButtonImage ParamMenu Digital effectOff*/Art/Sepia/Negative/ Monochrome/Vivid *Setting Value 18 White Balance Selecting [AUTO] under normal circumstances can choose white balance. If [AUTO] mode cannot produce natural colors, please use appropriate light conditions to change White Balance setting. Remote Controller MENU ButtonImage ParamMenuWhite BalanceAuto*/Incandescent/Sunny/Cloudy/ Fluorescent *Setting Value 19 ISO According to the brightness during shooting, selecting [AUTO] can set optimum ISO sensitivity. Remote Controller MENU ButtonImage ParamMenuISO Auto*/100/200/400/800/1600 *Setting Value 20 EV If "EV" is adjusted to + side, you can avoid under-exposure, or dark objects as shooting against a bright background. Playback button on the remote controllerSelect video clips with the remote controllerPress menu button on the remote controller SlideshowNo/1 second/2 seconds/3 seconds /5 seconds/10 secondsPress OK button on the remote controller to process. 41 Display all files During video preview, press key on the remote controller to enter video clips index. Select video clip and press OK key on the remote controller to confirm. 42 Connecting to PC Step 1 Insert the memory card into drive recorder (Page09), and take out the short USB cable provided. Step 2 Connect the USB cable with the drive recorder, and connect the other end to the USB port of PC. The red light will start blinking. Step 3 Press and hold the USB switch on the host device for 2~3 seconds to change to USB mode, now the red and blue lights will start blinking simultaneously. Step 4 The computer will show a removable disk, you can use this disk for data access in the memory card. 43 Q&A Q: Why does the blue light on the drive controller not light up (or sometime)?Blue light will stay OFF for the host device without GPS function; this is a normal phenomenon. For the host device with GPS function, blue light not lighting up means GPS is positioning. GPS signal will be affected by such factors as weather conditions, tunnels, and basements; the signal might be strong, weak or no signal, and this phenomenon will not affect the function of drive recorder, please be patient or go to open space to complete positioning. Please check whether your memory card is installed properly (See page09); otherwise, the data of the memory card is possibly full, please switch on the Recycle Record of the host device (See page24), and press FORMAT button on the host device (See page34) to solve the issue. 44 Q: How to achieve the best quality resolution?Please adjust the following parameters in Image Param (Please see page15). Video resolution Digital effect EV Contrast Sharpness 1920x1080 30P Vivid -1. 0 Hard Hard Q: Why doesn`t lights of the drive recorder react after inserting the power?A: Possibly it could be caused by the following circumstances: 1. Vehicle not started. [. . . ] A: Possibly it could be caused by the following circumstances: 1. Vehicle not started. If the abovementioned methods do not solve the problem, please contact our dealer or factory for product repair. A: It is because your computer does not have the encoder needed to play high definition video. Please search "K-Lite Codec Pack" in search engines, download and install the encoder; you will be able to play the file after installation. 45 Q: How to maintain the lens? [. . . ]