User manual DLS UR6S

[. . . ] The tweeter can also be installed on the dash-board, or recessed in the door with the accessories in the tweeter box. It is important to fasten the speakers properly in order to avoid bad sound or rattling. For speakers with separate filters in boxes or similar it is vital that they are attached properly to the interior of the vehicle to avoid rattling. Don´t place them close to the internal wiring of the car, this can cause interference. [. . . ] You don´t have to use the passive crossover if the system is connected to separate amplifiers and an active crossover. SPEAKER ENCLOSURES If you want to install the speaker in an enclosure the normal size for a closed box is: 5, 25" (13 cm) speakers 6, 5" (16, 5 cm) speakers 8" (20 cm) speakers : 6-8 liters : 10-12 liters : 15-20 liters These volumes are only a guideline. Contact your local DLS dealer for more exact information about your specific speaker. SPEAKER FACTS FOR DLS ULTIMATE SERIES Model Woofer Mid Tweeter Nom. power 120 W 150 W 120 W 150 W 80 W 100 W 80 W 100 W 80 W 100 W Max power 180 W 180 W 180 W 180 W 120 W 160 W 120 W 160 W 120 W 160 W Sensitivity 89 dB 88 dB 89 dB 88 dB 91 dB 91 dB 91 dB 91 dB 91 dB 91 dB Magnet size 62 mm / 2, 44" 62 mm / 2, 44" 62 mm / 2, 44" 62 mm / 2, 44" 85 mm / 3, 35" 85 mm / 3, 35" 85 mm / 3, 35" 85 mm / 3, 35" 85 mm / 3, 35" 85 mm / 3, 35" Inst. depth 58 mm / 2, 28" 63 mm / 2, 48" 58 mm / 2, 28" 63 mm / 2, 48" 62 mm / 2, 44" 65 mm / 2, 56" 62 mm / 2, 44" 65 mm / 2, 56" 62 mm / 2, 44" 65 mm / 2, 56" Mounting hole 120 mm / 472" 140 mm / 5, 5" 120 mm / 4, 72" 140 mm / 5, 51" 120 mm / 4, 72" 140 mm / 5, 51" 120 mm / 4, 72" 140 mm / 5, 51" 120 mm / 4, 72" 140 mm / 5, 51" Crossover UP5 UP6 UP35 UP36 UR5 UR6 UR5S UR6S 13 cm / 5, 25" 16, 5 cm / 6, 5" 13 cm / 5, 25" 16, 5 cm / 6, 5" 13 cm / 5, 25" 16, 5 cm / 6, 5" 13 cm / 5, 25" 16, 5 cm / 6, 5" 2, 5" 2, 5" 2, 5" 2, 5" 28 mm / 1, 1" 28 mm / 1, 1" 28 mm / 1, 1" 28 mm / 1, 1" 28 mm / 1, 1" 28 mm / 1, 1" 28 mm / 1, 1" 28 mm / 1, 1" 28 mm / 1, 1" 28 mm / 1, 1" Separate box Separate box Separate box Separate box Separate box Separate box Separate box Separate box Separate box Separate box UR35S 13 cm / 5, 25" UR36S 16, 5 cm / 6, 5" RUNNING-IN PERIOD Allow the speakers to play for at least 15-20 hours. SPEAKER PHASING To be sure to have the correct speaker polarity (phase) you can check this by using a 1, 5 Volt battery. Connect a cable from the battery plus-pole to the speaker plus, and a cable from the battery minus to the speaker minus. If the speakers are correctly connected the speaker cone should move outwards on both right and left channel. This check must be made on the cables going from the speakers, to the output terminals of your car stereo or amplifier. CONNECTION OF SPEAKERS Make sure you connect the cables with correct polarity to the speakers. The small terminal is minus. + - + - FILTER/CROSSOVER INSTALLATIONS Filter installation and connection of UP5 & UP6 Tweeter J2 Input Tweeter Midr. Woofer Filter installation and connection of UP35 & UP36 3-way systems Bass + + + + Mid Tweeter Speaker impedance 4 TWEETER + HI LO + 2-way crossover Mid level WOOFER + Coil J3 Tweeter level - - + INPUT BASS Head unit / amp. The tweeter level is adjustable in three steps, the MID level in two steps: TWEETER LEVEL: JUMPER J2 Select tweeter level by moving the small jumper J2 inside the filter box. High level Mid level Low level Tweeter level (J3): High = jumper in HI-position Mid = jumper in MID-position Low = jumper in LO-position Midrange level J2): High = jumper in HI-position Low = jumper in LO-position Jumper J1 is used when you want to run the system without midbass driver. Midbass disconnected: jumper mounted in OUT-position. J2 Tw level Hi Mid Low NOTE! If the system is used together with a subwoofer, test to phase reverse the subwoofer to see what sounds best. IN OUT + HI MID LO Bass/mid - J1 + _ _ _ _ FILTER/CROSSOVER INSTALLATIONS Filter installation and connection of UR5, UR6, UR5S & UR6S Tweeter TWEETER + + - 2-way crossover WOOFER + INPUT - + - Bass/mid + + Head unit / amp. Hi Mid Low J2 Tw level Filter installation and connection of UR35S & UR36S 3-way systems The drawing shows the connection of a 3-way system to one channel. The tweeter and mid levels are adjustable in two steps as described below: Tweeter level (J3): High = jumper mounted between pin 1-2. Jumper J1 is used when you want to run the system without midbass driver. Midbass disconnected: jumpers mounted between pin 1-3 & 2-4. - Jumper setting: TWEETER LEVEL Select tweeter level by moving the small jumper inside the filter box. level _ _ Bass Mid + + + + Tweeter J2 2 1 3 4 Mid level 2 4 J1 1 3 Car stereo / amp. _ _ Coil FACTS DLS UP2. 5 MID-DOME Size Nom. hole Cone Voice coil 2, 5" ( 6, 3 cm) 90 Watts RMS 160 Watts 400 Hz-8 kHz 91 dB / W / m 350 Hz 65 mm / 2, 56" 100 mm / 3, 94" 25 mm / 1" 82 mm / 3, 23" Doped fabric 52 mm / 2" al flat wire FACTS DLS UR2. 5 MID-DOME Size Nom. [. . . ] The cup is attached to the door side when the metal wings is pressed to the back side of the door. Put the tweeter element into the cup with the cable going out through the bottom hole. Then attach the element into the cup and turn it clockwise to attach to the cup. When removing the element from the cup, turn it ccw and lift it out F E RECESSED MOUNTING: A You need a hole with a diameter of 45 mm / 1, 77" in the door side. [. . . ]