User manual DLS REFSUB

[. . . ] In "open air" installations the power handling capacity is reduced by 30% from the nominal value. We dont recommend "open air" installations for Reference subwooers. W610, W612, W710, W712 MW10, MW12, MW110, MW112 SUBWOOFER ENCLOSURES, GENERAL Build your enclosure in a stable and airtight material. The size of the enclosure is decided by the speaker data. SEALED ENCLOSURES Sealed enclosures are easy to build. [. . . ] In a vented enclosure the sound from the speaker and the port work together creating a higher sound level. The sound from the port must come out in the same phase as from the speaker otherwise the result is bad. The size of the vented enclosure is decided by the speaker data just as for the sealed one. The size of the vehicle often decides the practical size of the enclosure. A smaller enclosure has a higher resonant frequency than the larger one. The size of the enclosure should not be so big that the speaker plays below it´s own free air resonance (Fs), then it looses in power handling capacity. The port does not have to be fully inside the enclosure as long as the area and length are correct. You can convert from one to two or more ports as long as the total port area is the same. All DLS subwoofers works well in vented boxes. + BANDPASS ENCLOSURES C In all bandpass enclosures the speakers are hidden inside the enclosure, all sound is coming out through the ports. There are different types of bandpass enclosures and they have in common that they are a bit more difficult to build. Most DLS subwoofers can be used in bandpass enclosures. Connected with a 12 dB passive low-pass x-over = 10 mH coil in series and a bipolar capacitor of 300 microFarad in parallel. Crossover frequency is 95 Hz. 87654321 87654321 87654321 87654321 L TECHNICAL SPECIFICATIONS FOR DLS REFERENCE SUBWOOFERS W610 Size Impedance Nom. range Sensitivity Voice coil diameter Voice coil height Re Voice coil inductance, 1 kHz BL product X-max Suspension compliance CMS SD- Effective piston area Resonant freq. (Fs) Vas (liters) Vas (ft3) Qms Qes Qts Cone material Magnet weight Magnet diameter Installation depth Mounting hole Outer diameter Weigth 25 cm (10") 4 ohm 180 W (max 360) 20 Hz- 1 kHz 89, 7 dB 50 mm (2") 22 mm (0, 87") 3, 6 ohm 1, 58 mH 15, 98 +-9 mm (0, 35") 290 314, 6 cm2 32, 9 Hz 40, 3 1, 42 3, 63 0, 23 0, 22 PPC 40 oz (1, 13 kg) 5, 7" (145 mm) 4, 29" (109 mm) 9, 13" (232 mm) 10, 31" (262 mm) 8, 16 lb (3, 7 kg) W612 30 cm (12") 4 ohm 210 W (max 400) 20 Hz-1 kHz 89, 2 db 50 mm (2") 22 mm (0, 87") 3, 3 ohm 1, 53 mH 15, 98 +-9 mm (0, 35") 271 452, 3 cm2 28, 1 Hz 77, 9 2, 75 3, 93 0, 32 0, 30 PPC 50 oz (1, 42 kg) 6, 14" (156 mm) 4, 72" (120 mm) 11, 18" (284 mm) 12, 2" (310 mm) 10, 14 lb (4, 6 kg) W710 25 cm (10") 4 ohm 200 W (max 400) 20 Hz- 1 kHz 90, 8 dB 50 mm (2") 22 mm (0, 87") 3, 6 ohm 1, 49 mH 17, 43 +-9 mm (0, 35") 308 314, 6 cm2 32, 4 Hz 42, 8 1, 51 3, 76 0, 19 0, 18 PPC 80 oz (2, 27 kg) 5, 7" (145 mm) 5, 08" (129 mm) 9, 13" (232 mm) 10, 31" (262 mm) 11, 68 lb (5, 3 kg) W712 30 cm (12") 4 ohm 250 W (max 480) 20 Hz-1 kHz 91 dB 50 mm (2") 22 mm (0, 87") 3, 24 ohm 1, 43 mH 16, 69 +-9 mm (0, 35") 279 452, 3 cm2 28, 8 Hz 80, 2 2, 83 3, 13 0, 23 0, 21 PPC 100 oz (2, 83 kg) 6, 14" (156 mm) 5, 51" (140 mm) 11, 18" (284 mm) 12, 2" (310 mm) 13, 56 lb (6, 15 kg) RECOMMENDED ENCLOSURES FOR W610, W612, W710 & W712 RUNNING-IN PERIOD Allow the speaker to play for at least 15-20 hours. Subwoofer W610 W612 W710 W712 Volume (liters/ft3) vol: 35, 6 / 1, 25 vol: 41, 8 / 1, 47 vol: 35, 4 / 1, 25 vol: 45, 6 / 1, 61 F3 = approximative lower frequency for vented boxes in Hz. Fb = Box resonant frequency Damping Line inside Line inside Line inside Line inside F3 43, 4 Hz 45, 6 Hz 45, 4 Hz 50, 4 Hz Fb 43, 0 Hz 39, 1 Hz 45, 0 Hz 45, 0 Hz VENTED ENCLOSURE Port 4" x 32 cm/12, 6" 4" x 35 cm/ 13, 7" 4" x 29 cm/11, 4" 4" x 19, 5 cm/7, 7" SEALED BANDPASS The speaker is installed in Vb1 playing into chamber Vb2 where the port(s) are installed. Vb1=rear, Vb2=front SEALED ENCLOSURE W610 Vb1 Vb2 port Vb2 19, 0 18, 6 1x10, 2x19 cm 0, 67 ft3 0, 66 ft3 1x4"x7, 5" (US) F3 Vb1: 45 Hz, Vb2: 108 Hz W710 Vb1 Vb2 port Vb2 25, 08 18, 5 1x10, 2x23, 5 cm 0, 88 ft3 0, 65 ft3 1x4"x9, 25" (US) F3 Vb1: 40 Hz, Vb2: 106, 6 Hz We don´t recommend the use of sealed enclosures for these subwoofers W612 Vb1 Vb2 port Vb2 31, 65 38, 61 2x10, 2x19 cm 1, 12 ft3 1, 36 ft3 2 x 4" x 7, 5" (US) F3 Vb1: 45 Hz, Vb2: 96, 7 Hz W712 Vb1 Vb2 port Vb2 33, 97 19, 4 1x10, 2x17, 5 cm 1, 2 ft3 0, 68 ft3 1 x 4" x 6, 9" (US) F3 Vb1: 40 Hz, Vb2: 120, 5 Hz TECHNICAL SPECIFICATIONS FOR DLS REFERENCE SUBWOOFERS MW110 Size Impedance Nom. range Sensitivity Voice coil diameter Voice coil height Re Voice coil inductance, 1 kHz BL product X-max Suspension compliance CMS SD- Effective piston area Resonant freq. (Fs) Vas (liters) Vas (ft3) Qms Qes Qts Cone material Magnet weight Magnet diameter Installation depth Mounting hole Outer diameter Weigth 25 cm (10") 4 ohm 350 W (max 550) 25 Hz- 2 kHz 87 dB 75 mm (3") 24 mm (0, 94") 3, 2 ohm 1, 22 mH 12, 58 +-9 mm (0, 35") 197 314, 6 cm2 36, 7 Hz 27, 5 0, 97 2, 34 0, 44 0, 37 Magnesium 50 oz (1, 42 kg) 6, 14" (156 mm) 4, 33" (110 mm) 9, 21" (234 mm) 10, 31" (262 mm) 10, 6 lb (4, 8 kg) MW112 30 cm (12") 4 ohm 350 W (max 550) 20 Hz-2 kHz 90 db 75 mm (3") 24 mm (0, 94") 3, 34 ohm 0, 99 mH 16, 35 +-9 mm (0, 35") 205 452, 3 cm2 31, 8 Hz 58, 8 2, 08 1, 71 0, 31 0, 26 Magnesium 70 oz (1, 98kg) 7, 09" (180 mm) 4, 80" (122 mm) 11, 10" (282 mm) 12, 2" (310 mm) 14, 3 lb (6, 5 kg) MW10 25 cm (10") 4 ohm 400 W (max 600) 25 Hz- 2 kHz 89 dB 75 mm (3") 24 mm (0, 94") 3, 23 ohm 1, 26 mH 14, 20 +-9 mm (0, 35") 202 314, 6 cm2 35, 1 Hz 28 1, 51 2, 32 0, 36 0, 31 Magnesium 100 oz (2, 83 kg) 6, 14" (156 mm) 5, 11" (130 mm) 9, 21" (234 mm) 10, 31" (262 mm) 14, 77 lb (6, 7 kg) MW12 30 cm (12") 4 ohm 400 W (max 600) 20 Hz-2 kHz 91 db 75 mm (3") 24 mm (0, 94") 3, 57 ohm 0, 95 mH 18, 94 +-9 mm (0, 35") 210 452, 3 cm2 37, 1 Hz 60, 2 2, 83 2, 14 0, 24 0, 21 Magnesium 140 oz (3, 97 kg) 7, 09" (180 mm) 5, 59" (142 mm) 11, 10" (282 mm) 12, 2" (310 mm) 19, 6 lb (8, 9 kg) RECOMMENDED ENCLOSURES FOR MW10, MW12, MW110 & MW112 RUNNING-IN PERIOD Allow the speaker to play for at least 15-20 hours. [. . . ] In sedan vehicles with the passenger compartment separated from the trunk, the enclosure should be installed with booth speaker and port directed towards the rear seat. Some cars have an opening in the middle of the rear seat for loading skis etc. You can install the enclosure behind this opening and direct speaker or port through this opening. [. . . ]