User manual DLS CAD11

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual DLS CAD11. We hope that this DLS CAD11 user guide will be useful to you.


DLS CAD11 : Download the complete user guide (308 Ko)

Manual abstract: user guide DLS CAD11

Detailed instructions for use are in the User's Guide.

[. . . ] Check the voltage with a multi meter. Installation Before you begin installation Before you begin you need to read the manual, to have some tools, cables and other material available. There is one such list of material on the following page. Amplifier protection fuse blows at low volume: One or more speaker cables are shorted. The cables must not have a connection to earth. Amplifier location Important Allow air circulation around the amplifier. The DLS Classic series of amplifiers have a compact design that allows great flexibility in mounting. [. . . ] You can either use a crimp fork terminal or insert the cable directly into the amplifier terminal. If there is no remote voltage available from the stereo, you must connect to the ignition key through the radio or any accessories fuse. For High Level input: We recommend you to connect the remote wire as described above. You must set the Hi level/Low level switch to Low level position in this case. In the case that there is no remote voltage available from the car stereo or you want to simplify the installation, the amplifier can be turned on/ turned off by the high level input voltage. This is done when the Hi level/Low level switch is set to Hi level position. There is a small disadvantage that this function gives soft turn off operation but some plop sound when switching off. +12V REM GND +12V REM GND DLS DLS FH 2B fuse holder Connect the battery cable to the +12 Volt on the amplifier. If you want to improve the power capacity you can add a Power capacitor of 1 Farad in parallel with the DC input. Be sure to use a rubber grommet or a plastic insulating tube where the cable passes the firewall or other places when it can easily be jammed. Use wire ties to secure to existing cables in the engine room. Ground Terminal ( GND ) Connect to a good chassis ground. The ground connection should be clean, unpainted metal to provide a good electrical connection. Use a wire brush, a scraper or a piece of an abrasive sheet to clean the metal. +12V REM GND +12V REM GND Power Light / Protect light The power light (green ) comes on when the amplifier is turned on. Power (Green) The protect light ( red ) comes on when the amplifier shuts down from overheating or short circuit. Protect (Red) Fuses Use only 30 ampere ATC blade type fuses. 4 30A Input and controls 21 21 21 21 21 Input Wiring Inputs may be low level from the RCA output of the car stereo or high level from the car stereo speaker output. Low level = RCA is to prefer for the best sound quality. Important Use either the low level or the high level input, do not use both at same time. Low level input Use a pair of shielded stereo audio cables with RCA type jack. Most trunk-mount amplifiers need a 20 feet RCA cable ( appr 5 ­ 6 meters). Most under the seat installations require 12 feet ( 2 ­ 3 meters) RCA cables. Avoid placing the RCA cable close to speaker cables, power cables and remote control cable. High Level Input Connect left and right speaker wires coming from the car stereo to the high level input as shown. You must connect both plus and minus as the inputs are balanced, connecting plus only gives lower level and bad sound quality. [. . . ] Tap the + wire on to the + terminal of the battery, and observe the movement of the cone. The cone should move outwards when the wire touches the battery, and inwards when the battery is removed. If it is the other way around, the speaker has been connected backwards and it must be removed and connected correctly. If your system also has a subwoofer connected through a passive 6 or 12 dB crossover, try to connect this with various polarity and judge what sounds best. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE DLS CAD11




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual DLS CAD11 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.