User manual DAXTEN Z-SERIES BROCHURE

[. . . ] 1-732-764-8887 E-mail: sales@raritan. com http://www. raritan. com Raritan Computer Europe, B. V. 31-10-284-4049 E-mail: sales. europe@raritan. com http://www. raritan. com Raritan Computer Japan, Inc. Kuga Building 7F 11-6, Kuramae 4-chome Taitoo-ku, Tokyo 111-0051, Japan Tel. 81-3-5833-6336 E-mail: sales. japan@raritan. com http://www. raritan. co. jp Raritan Computer Taiwan, Inc. [. . . ] Press <Enter> to switch to the selected computer/channel. Figure 9. [F2] Selection Menu Alternatively, you may switch between computers without using the OSUI, by using the UP and DOWN buttons in the front of the USTS user station. These buttons switch between computers by name in alphabetical order: UP switches to the previous computer by name in alphabetical order; DOWN switches to the next computer by name in alphabetical order. Edit Menu The Edit Menu <F3> (Figure 10) can be used to make changes to the computer channel name and its scan ratethe time interval, in seconds, that a channel's computer is to remain displayed on monitor during scanning. It can also be used to designate a channel as a <Home> computer. Press < >, < >, <>, or <> to highlight (in yellow) the field to be edited 2. Press the <Home> key if you wish to designate this computer/channel as your home computer. This designation will enable the user to quickly select or switch directly to the home computer. At the Selection Menu, pressing the <Home> key once highlights the home channel. With no OSUI displayed, rapidly pressing the <Home> key twice automatically switches the user to the computer designated as the home computer. Press <S> to save changes and exit, or <ESC> and then <N> to exit without saving changes. Verify that new name appears on Selection Menu in green. Figure 10. [F3] Edit Menu Operating Z4200U 11 System Profile Menu The System Profile Menu <F4> (Figure 11) can be used to make changes to parameters that effect overall system functionality. Select fields to be edited by pressing <Tab> (moves forward) <Shift-Tab> (moves backward), < >, < >, < >, or < > keys to move to desired field. Use the < >, < > keys to select choices in each field or make entries as explained below. Press <S> to save changes, and <ESC> to exit System Profile Menu. To exit System Profile Menu without saving changes, press <ESC> and then <N> or <ESC> again. Figure 11. [F4] System Profile Menu · Scan Mode: By pressing <F6> to toggle ON scan mode, the user station can scan through all attached computer channels at a specified time interval. When scan mode is activated the word "Scan" at the bottom of the OSUI is highlighted in yellow. - - Global: Scans each channel for the same amount of time, as indicated under Global Scan Rate. Individual: Scans each channel for the specified time set per channel, as shown in Selection Menu. (Setting each channel's individual scan rate is a function of the Edit Menu <F3>, where individual channel scan times can be set between 03 and 30 seconds. Default is 03 seconds. ) · Global Scan Rate: Sets the time duration for which each channel will be scanned. Use the < > and < > keys to set between 03 and 30 seconds. [. . . ] See Appendix A: UTP Cabling FAQs for Raritan certified Category 5e UTP cable recommendations. The Z-CIM's indicator light is flashing rapidly, rather than blinking steadily, after connection to the computer and the Z-Series chain. In addition, there is no indication of an active computer on the Selection Menu (no green channel). The video quality that I see is blurry, or exhibits color seperation and/or ghosting. Ensure that the cables connected the Z-CIM to the computer, and the cables connecting the Z-CIM to the Z-Series chain, are connected properly and securely 1. 2. Adjust the "Video Adjustment" control on the back of your USTS unit. [. . . ]