User manual DAXTEN DSR 2161

[. . . ] DS R DSR1161 Installer/User Guide DSR2161 DSR4160 ii DSR Installer/User Guide INSTRUCTIONS The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. DANGEROUS VOLTAGE The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. POWER ON This symbol indicates the principle on/off switch is in the on position. POWER OFF This symbol indicates the principle on/off switch is in the off position. PROTECTIVE GROUNDING TERMINAL A terminal which must be connected to earth ground prior to making any other connections to the equipment. DSR Installer/User Guide Avocent, the Avocent logo and "The Power of Being There" are trademarks of Avocent Corporation. All other marks are trademarks or registered trademarks of their respective owners. All rights reserved. USA Notification Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. [. . . ] However, depending on your system, you may wish to fine-tune some aspects of its performance. To change your default desktop size There are occasions when you may wish to change the resolution on your desktop to one resembling the Host system. Select Tools-Desktop from the command bar at the top of the Session window. Repeat this command to return to your original resolution. 32 DSR Installer/User Guide To program a keyboard macro If you require a key sequence that is not pre-programmed into the DSR, you can add a macro by performing the following steps: 1. The Keyboard Macro Configuration window will appear listing the currently available macros. 4. 5. 6. 7. The Add Keyboard Macro dialog box will appear. Enter a unique description for the macro in the space labeled Macro Description. In the window titled Double-click for Key Press, double-click the first keystroke of your macro. This will move the keystroke to the window labeled Double-click for Key Release. If this key needs to be released before the next keystroke is entered, double-click the keystroke in the Double-Click for Key Release window to move it to the Macro Created window. If not, leave this key in the DoubleClick for Key Release column at this time. Now, double-click on the remaining commands, if any, under the Doubleclick for Key Release window in the order in which you would like them released to move them to the window labeled Macro Created. The Macro Created window will now list the key sequence in the exact order that it will be performed by the system. There should be no keys remaining in the center column under Double-click for Key Release. It will now appear in the Macro list and also in the macro commands on every host window. Chapter 4: Advanced Operations 33 For example: To create a macro where the Control key is held while F1-F2-F3 are typed: 1. We have named this one Control F1-F2-F3. 2. 3. 4. 5. The Control key is pressed first and held, so double-click on the Left or Right Ctrl keystroke under Double-click for Key Press. It will move to the second window and the command Press [Left Ctrl] will appear in the third window. Locate F1 in the Doubleclick for Key Press window and double-click it. It will move to the second window and the command Press [F1] will appear in the third window. F1 will be released before F2 is pressed, so you will need to double-click on F1 under the Double-click for Key release window before proceeding. This will create a command in the Macro Created window that displays Release F1 and then F1 will disappear from the second window. Repeat Step 3 and 4 with F2 and F3. 34 DSR Installer/User Guide 6. The last step is to release the Control key. The command Release [Left Ctrl] will appear in the 3rd window. 7. The keystrokes will be listed in correct order in window three. [. . . ] All communication between the DS1800 and the DSView client takes place over TCP/IP port 8192 until the DSView client closes the session. DSAuth Server TCP/IP Port 8191 Avocent Authentication Service Avocent Service DS/DSR unit TCP/IP TCP/IP Port 8192 Port 2068 DSView Client DSAdmin Client Remote User If the DSView user wishes to establish a session with another DS1800 port, the same process is used. DSAuth Server TCP/IP Port 8191 Avocent Authentication Service Avocent Service DS/DSR unit TCP/IP TCP/IP Port 2068 TCP/IP Port 8190 TCP/IP Port 8192 Port 2068 TCP/IP Port 8192 DSView Client DSAdmin Client DS/DSR unit Remote User 66 DSR Installer/User Guide DSAdmin functions similarly to the DSView client. It establishes a connection using TCP/IP port 2068, and uses the same process for authentication and return of the browse list. Changes made to the browse list through DSAdmin are transmitted back to the DSAuthentication Server using TCP/IP port 8190. After the changes are made, DSAdmin refreshes its browse list view over the TCP/IP port 2068 connection. [. . . ]