User manual DANBY DPR2262

[. . . ] Adjusting the Air Flow Direction Horizontally . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Adjusting the Air Flow Direction Vertically . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 7 8 9 9 RECOMMENDATIONS FOR USE Power Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Temperature and Humidity Ranges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cleaning Your Air Conditioner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Cleaning Your Air Conditioner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Solving Common Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 10 11 12 13 E-3 Description of Each Component Design and shape are subject to change. Air outlet - Except AAC5040/AAC5040-1 Outer air flow blades (up/down orientation) Inner air flow blades (right/left orientation) Air outlet Ventilation lever - Except AAC5040/AAC5040-1 Air inlet (Inside) Air inlet (Outside) Air filter (Inside) Power plug (The type of power plug may differ, depending on the local power supply. ) Operating mode selection dial Thermostat control Selector Thermostat E-4 Getting Started Your Owner's Instructions contain much valuable information on using your air conditioner. Please take the time to read them as they will help you take full advantage of the unit's features. The illustrations in the step-by-step procedures use four different symbols: PRESS PUSH IMPORTANT NOTE E-5 Cooling Your Room You must select the COOL mode if you wish to adjust the: Cooling temperature Fan speed when Cooling 1 Turn the operating mode selection dial and set it to " Hi Cool " , " Med Cool " or " Low Cool ". You can change modes at any time. 2 Turn the THERMOSTAT control to the desired position. Result: The air conditioner starts cooling if the room temperature is higher than the selected temperature. 3 To control the direction of the air flow, refer to page 9. E-6 Ventilating Your Room If the air in your room is stale, you can ventilate the room using the Fan feature. (Except AAC5040/AAC5040-1) 1 If you wish to discharge stale air, push the ventilation lever on the front of the unit to the right and open position ( ). Result: The air inside the room circulates and stale air is discharged outside. ). Otherwise, push the ventilation lever to the left and closed position ( Result: The air simply circulates inside the room. 2 Turn the operating mode selection dial and set it to "Hi Fan" or "Low Fan" position. - When the number on the THERMOSTAT control is too high, the room temperature may be too warm. Check to see whether there is an open window or leakage of cool air to the outside. Check to see whether there is any obstacle adversely affecting the flow of the air inside and outside the room. Check to see whether the air filter is clogged with dust or contaminated with foreign substances. Check to see whether there is any direct sunlight facing the air conditioner. Ventilate the room. The air comes out smoothly, but cooling is not effective. Odors are permeating the room during air conditioning. E-12 Technical Specifications Design and specifications are subject to change without notice. Model AAC5040/AAC5040-1 Power Supply 115V~, 60Hz E-13 LIMITED AIR CONDITIONER WARRANTY This quality product is warranted to be free from manufacturer's defects in material and workmanship, provided that the unit is used under the normal operating conditions intended by the manufacturer. This warranty is available only to the person to whom the unit was originally sold by Danby or by an authorized distributor of Danby, and is non-transferable. TERMS OF WARRANTY First 2 Years Third Through Fifth Year To obtain Service During the first 2 year (2), any electrical parts of this product found to be defective, including any sealed system units, will be repaired or replaced, at warrantor's option, at no charge to the ORIGINALpurchaser. During the next three years (3) any part of the sealed system found to be defective (consisting of compressor, condenser, evaporator, dryer and all related tubing) will be repaired without charge. [. . . ] TERMS OF WARRANTY First 2 Years Third Through Fifth Year To obtain Service During the first 2 year (2), any electrical parts of this product found to be defective, including any sealed system units, will be repaired or replaced, at warrantor's option, at no charge to the ORIGINALpurchaser. During the next three years (3) any part of the sealed system found to be defective (consisting of compressor, condenser, evaporator, dryer and all related tubing) will be repaired without charge. Contact your dealer from whom your unit was purchased, or contact your nearest authorized Danby service depot, where service must be performed by a qualified service technician. If service is performed on the units by anyone other than an authorized service depot, or the unit is used for commercial application, all obligations of Danby under this warranty shall be at an end. EXCLUSIONS Save as herein provided, Danby Products Limited (Canada) or Danby Products Inc. [. . . ]